American Standard 7510.103, 790767-100 User Manual
™
CULINAIRE COLLECTION™
STAINLESS STEEL
KITCHEN SINKS
MODELS 7501.103, 7502.103, 7502.403,
7504.103, 7507.103, 7510.103
SELF RIMMING
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
BEFORE YOU BEGIN...
Unpack new sink and inspect carefully for
damage. Replace the sink in its original packing
carton to protect it until you are ready to begin
installation.
Recommended Tools & Materials
Putty Knife
Pipe Wrench
Channel Locks
Long Phillips Screwdriver
or Regular Screwdriver
Adjustable Wrench
Drill
Basin Wrench
Saber Saw
Plumber's Putty or Caulk
Tubing Cutter
Tape Measure
Hacksaw
Mineral Spirits
Silicone Sealant
Below are the dimensions needed to determine the cutout size
for each sink. Select the correct diagram for your sink and refer
to the instructions below.
Locate and mark center lines of sink on countertop.
Provide proper clearance under the countertop for the faucet
supply lines and the structural parts of the cabinet.
By using the diagrams below and measuring your sink, draw the
outline of the sink cutout onto the countertop. This is the cutting
outline.
Remember that the size of the sink is larger than the cutout.
CUTOUT DIMENSIONS FOR SINKS:
Certified to comply with ANSI A112.19.3M
CAN/C.S.A. B-45
Observe local plumbing and building codes.
790767-100
Countertop Cutout Dimensions
32-1/8
(816mm)
21-1/8
(537mm)
CULINAIRE DOUBLE BOWL SINK
MODEL 7502
21
(533mm)
CULINAIRE DUAL LEVEL
32
(813mm)
BOWL SINK
MODEL 7504
17
(432mm)
21
(533mm)
CULINAIRE ISLAND SINK
MODEL 7507
(533mm)
21
21-1/8
(537mm)
CULINAIRE SINGLE BOWL SINK
38
(965mm)
CULINAIRE DUAL LEVEL SINK
WITH DRAIN BOARD
MODEL 7510
24-1/4
(616mm)
MODEL 7501
IMPORTANT: DIMENSION OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN
THE RANGE OF TOLERANCES ESTABLISHED BY A.N.S.I. AND C.S.A. STANDARDS.
1
©AMERICAN STANDARD INC. 2002
AFTER THE CUTOUT IS DRAWN...
1
Drill a clearance hole
inside the cutout line
as marked on the
countertop.
2
Cut opening on cut line
inside the perimeter of sink.
Note - Formica countertop
installation only is illustrated.
Contact your countertop
distributor for the best method
of cutting other materials such
as marble, hard synthetics,
etc.
3
Mount the faucet and
drain assembly on the
sink or countertop
following the
manufacturer's
instructions.
Perimeter
of sink
Perimeter
of sink
Cutout
Cutout
7
8
9
Rotate each
retaining clip
toward sink bowl.
Apply a generous portion of sealant inside line
traced on countertop. Carefully lower sink into
cutout and press down firmly. Use guidelines
for proper positioning.
Rotate each clip to
engage countertop.
NOTE - TIGHTEN
THE TWO CENTER
CLIPS ON EACH
LONG SIDE OF THE
SINK FIRST ( SEE
FIGURE 3 FOR DETAILS). Complete the
tightening process for the remaining clips,
to secure sink. Remove excess sealant from
countertop for a smooth even line of sealant
around the edge of the sink.
Before applying the sealant,
4
place the sink temporarily
into the cutout. Check for
alignment and clearance,
then trace around the
outside edge of the sink as
a guide for installation
location and application
of sealant.
Remove sink and
5
apply a masking tape
outline 1/8" outside
traced outline as a
guide for application
of silicone sealant.
6
Cutout
Masking
tape outline
LOCKING TAB
1/8"
Sink
outline
10
11
Connect supply lines
to faucet finger tight,
and carefully bend to
engage with the
supply stops. Tighten
connections to faucet
for secure seal.
Connect drain assembly
hand tight to check alignment. It may be necessary
to cut off part of the
tailpiece (area "A") or part
of the horizontal leg of the
trap (area "B").
Secure joint for watertight
assembly.
Trap
Single Bowl Double Bowl
A
Trap
B
Place a retaining clip onto hold-down rib. Make
certain locking tab engages depression in
hold-down rib. Approximate locations shown
on page 3 for correct model.
790767-100
NOTCH
12
2
Note: The clips supplied with sink can be used for
a countertop with a thickness of 1/2" min. to 1"
max. If countertop excedes 1" thickness you must
request clips for the larger thickness. Part No.
790772-0070A. If a plug is required to cover an
unused hole, order Part No. 790773-0070A.
©AMERICAN STANDARD INC. 2002
Tightening Sequence For Clips
11 3 1 9 11 6 2 4 13
7
8
5
6
12 2 4 10
MODEL 7501
9
10
7
8
12 3 1 5 14
MODEL 7502 & 7504
5
7
42
MODEL 7507 MODEL 7510
©AMERICAN STANDARD INC. 2002
11 513
8
6
9
10
1313
7
8
12 4 2 6 14
3
790767-100
Loading...