American Standard 7831, 4802, 4800, 7830, 7890 User Manual

...

Installation Instructions

4800 SERIES 4801 SERIES 4802 SERIES

HERITAGE SERIES SPREAD LAVATORY

FAUCETS

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

7830 SERIES 7831 SERIES 7890 SERIES

Certified to comply with ANSI A112.18.1M U.S. Patent No. 5,819,789

34312M-D

4800 SERIES

CONVENTIONAL

SPOUT LESS POP-UP

7831 SERIES

GOOSENECK SPOUT

WITH POP-UP

HANDLE

SCREW

CARTRIDGE

ESCUTCHEON

RUBBER

RING

RUBBER

WASHER

BRASS

WASHER

LOCKNUT

4801

SERIES

HERITAGE

SPOUT

W/POP-UP

RUBBER

GASKET

LOCKNUT

SEAL

WASHERS

SCREW

EXTENSION

LIFT ROD

O-RING

RUBBER

WASHER

RETAINER

TUBE & TEE

ASSEMBLY

O-RING

THUMBSCREW

EXTENSION

ROD

WRENCH

AERATOR

VALVE

ASSEMBLY

STOPPER

FLANGE

DRAIN

GASKET

DRAIN

WASHER

DRAIN

NUT

7890 SERIES

GOOSENECK SPOUT

BAR SINK

Printed in Mexico

COUPLING

NUT

SPOUT ASSEMBLY (Model 7890 only)

CAUTION

Turn off hot and cold water

supplies before beginning.

Apply the grease (provided) liberally to the SPOUT O-RINGS and SNAP RING areas.

Assemble the SPOUT and tighten SPOUT NUT until snug on VALVE BODY.

Tighten BRASS LOCKNUT on center body.

CLIP

PIVOT

ROD

SPOUT

NUT

SPOUT

O-RINGS

SNAP RING

ESCUTCHEON

DRAIN

BODY

TAILPIECE

SPOUT OR BASE ASSEMBLY (continued)

Insert BASE or SPOUT shank through center hole of SINK, making sure RUBBER GASKET is properly positioned.

Assemble RUBBER WASHER, RETAINER, and LOCKNUT onto threads of SPOUT from underside of SINK.

Insert LIFT ROD through SPOUT (or BASE) and slot of RETAINER.

Align SPOUT and tighten LOCKNUT. Be sure slot in BRASS WASHER is positioned to the rear as shown.

VALVE INSTALLATION

Insert VALVE BODY through hole from underside of SINK. Thread of VALVE BODY should extend at least 5/16 inch above SINK top. If necessary, adjust LOCKNUT.

Place RUBBER RING into ESCUTCHEON and screw ESCUTCHEON onto VALVE BODY until snug against internal stop.

Set VALVE BODIES so that their outlets are facing toward center of SINK. Tighten LOCKNUT using wrench supplied with faucet.

Before connecting TEE make certain that O-RINGS are properly seated on stepped SHANK and SCREW.

RUBBER

GASKET

SINK

5/16'' MIN.

SPOUT

RUBBER

WASHER RETAINER

LOCKNUT

ESCUTCHEON

RUBBER RING

LEDGE

RUBBER WASHER

BRASS WASHER

LOCKNUT VALVE

BODY

Push SCREW into TEE and tighten SCREW onto SHANK to secure SPOUT connection.

Place WASHERS inside COUPLING NUTS and connect HOSE to each valve outlet. Tighten COUPLING NUTS.

Connect HOT water supply to the left VALVE and the COLD water to the right VALVE using sealant and appropriate connectors and coupling nuts.

Refer to separate "Instruction Sheet" for assembly of handles.

DRAIN ASSEMBLY

(Model 4802 only)

Apply a bead of PUTTY around underside of DRAIN PLUG flange. Insert DRAIN PLUG into SINK drain hole.

Hold DRAIN PLUG to prevent turning and assemble GASKET, WASHER, and LOCKNUT, from underneath sink.

Insert threaded end of TAILPIECE into lower end of DRAIN PLUG. Connect other end to trap.

PUTTY

RUBBER

GASKET

LOCKNUT

TAIL

PIECE

FLANGE

SHANK

O-RING

TEE O-RING

SCREW

SINK

DRAIN

PLUG

WASHER

INSTALL POP-UP DRAIN

Push TAILPIECE down into TRAP (threaded end up).

Thread LOCKNUT, WASHER and GASKET onto DRAIN BODY.

Apply a bead of PUTTY to underside of FLANGE.

Feed DRAIN BODY up through SINK and thread FLANGE fully onto BODY.

Tighten LOCKNUT firmly, keeping the PIVOT ROD pointed towards the back of the SINK.

Drop STOPPER into DRAIN BODY. Pull TAILPIECE up and thread tightly

into DRAIN BODY.

TEST INSTALLED FAUCET

Remove AERATOR. With handle in OFF position, turn on water supplies and check

all connections for leaks.

SERVICE

To change direction of handle rotation, proceed as follows:

Turn valve to OFF position. Remove INSERT and HANDLE SCREW. Slip HANDLE with ADAPTER off. Remove SPRING CLIP. Lift STOP WASHER, turn 90° and replace. Replace SPRING CLIP. Replace ADAPTER, HANDLE, SCREW, and INSERT.

AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean.

HOTLINE FOR HELP

For toll-free information and answers to your questions, call:

1 (800) 223-0068 Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time Saturdays 8:00 a.m. to 4:00 p.m. Eastern Time

FLANGE

SINK

LOCKNUT

SPRING

CLIP

STOPPER

PUTTY

STOP

WASHER

GASKET

WASHER

PIVOT

ROD

TAILPIECE

TRAP

Position EXTENSION ROD onto POP-UP ROD and tighten THUMBSCREW.

Remove one end of CLIP from PIVOT ROD by squeezing ends together while sliding.

Insert PIVOT ROD into second or third hole in EXTENSION and reassemble CLIP. (EXTENSION may need to be bent.)

Adjust STOPPER height by repositioning EXTENSION and tightening THUMBSCREW.

TAILPIECE

POP-UP ROD

EXTENSION

ROD

CARTRIDGE

SCREEN

PIVOT

ROD

THUMBSCREW

DRAIN

BODY

TRAP

EXTENSION

ROD

CLIP

Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks.

Operate LIFT ROD and check DRAIN for leaks. Turn handles into OFF position and replace AERATOR.

If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°.

Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow. To clean, first turn off hot and cold water supplies, then:

Remove INSERT and HANDLE SCREW. Slip HANDLE with ADAPTER off. Unscrew CARTRIDGE with wrench. Thoroughly rinse plastic SCREEN at base of CARTRIDGE.

Replace CARTRIDGE until flange is tight against valve body. Turn valves OFF. Replace ADAPTER, HANDLE, SCREW, and INSERT.

Product names listed herein are trademarks of American Standard Inc.

CLIP

34312M-D