American Standard 7820.800 User Manual

7301050-100 Rev.C

P ro d u ct na m e s l i s te d he r ei n ar e t r a de m a r ks o f A m e ri c an S ta n da r d I n c.
© A m e ri c an S ta n d a rd I nc . 2 0 0 7

ASSEMBLY & INSTALLATION
INSTRUCTIONS

Cascada 30" Vanity

9437.200

Newbern Vanity Top

7820.800

- 1 -

Recommended Tools & Materials

Roughing-in Dimensions

Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years.
To help insure that the installation process will proceed smoothly, please read these instructions carefully before you
begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.

Adjustable Wrench

Channel Locks

Phillips Screwdriver

Putty Knife

Regular Screwdriver

Drill

Saber Saw

Level

Basin Wrench

Plumbers' Putty or
Caulking

Tubing Cutter

10'

Tape
Measure

Hacksaw

Pipe Wrench

™

21"

533mm

30"

762mm

34"

864mm

22-3/4"

578mm

26-3/4"

679mm

6"

(152mm)

1-1/4" O.D.

WASTE

SUPPLIES
AS REQ'D

FINISHED FLOOR

To maintain the beauty of the finish, avoid placing the furniture in direct sunlight, as sunlight causes fading. Also avoid
extreme changes in temperature by arranging furniture away from radiators, heat and air vents, and air conditioning
units. Avoid placing furniture directly under windows.

- 2 - - 3 -

C/L of 2 x 6
Reinforcement

Finished
Floor

27-3/4"

Provide suitable reinforcement required for anchoring the vanity to the wall. Centerline of reinforcement should be 27-3/4" up from the
floor (see Figure 1).

Open vanity drawers. Remove screws from inside drawers and pull drawers off drawer glides. (see Figure 2).

If molding is present, it will need to be notched to set the vanity flush against the wall. (see Figure 3).

Rough in supply lines and waste per rough in dimensions.

NOTE:

If current supply lines are greater than 6" on center,

they may interfere with cutout in rear of vanity or vanity shelf.

Move the vanity into place and level with the adjustable
glides on the bottom of the feet. The glides can be adjusted
outward up to 3/4" but it is recommended not to exceed 1/2"
if possible. Anchor it to the wall through at least 2 of the
anchoring holes in the rear of the vanity (see Figure 4).

Installing the Newbern Top…

Two people recommended for this installation

Mount the drain assembly (not included) on the sink. Be certain to apply
a bead of sealing putty on the underside of the drain (Part "A") in order to
ensure a watertight seal between the sink and drain. Remove excess
putty after installing the drain on the sink.

Apply a bead of silicone adhesive to the rim of the vanity. Place the
Newbern top centered left to right on the vanity and with the back edge of
the top even with the rear of the vanity. Clean up any excess silicone.

Place top back on vanity and, connect the trap to the drain assembly
hand tight to check alignment. It may be necessary to cut off part of the
tailpiece (area "B") or part horizontal leg of the trap (area "C").

Connect hot and cold supply lines to the shut off valves. Tighten trap
joints for watertight assembly.

A

B

C

VANITY INSTALLATION

MOLDING

ADJUSTABLE GLIDES
(LOCATED UNDER
EACH FOOT)

FIGURE 1

FIGURE 3

21

(533mm)

C/L

27-1/2"
578mm

Using a 3/8" O.D. drill, drill 3 anchoring
holes, equally spaced, in back support of
vanity (see Figure 4).

Continue with installation appropriate for
top and sink options chosen.

FIGURE 4

ANCHORING

HOLES (3)

FIGURE 2

DRAWER

REMOVE
SCREWS