American Standard 7820.400 User Manual
™
ASSEMBLY & INSTALLATION
INSTRUCTIONS
Newbern Vanity Top™
7820.400
Fits most 30" X 21" Vanity Bases
Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years. To help insure that the installation
process will proceed smoothly, please read these instructions carefully before you begin. Also, review the recommended tools and materials list;
carefully unpack and examine your new plumbing fixture.
To maintain the beauty of the finish, avoid placing the furniture in direct sunlight, as sunlight causes fading. Also avoid extreme changes in
temperature by arranging furniture away from radiators, heat and air vents, and air conditioning units. Avoid placing furniture directly under windows.
Recommended Tools & Materials
Basin Wrench Plumbers' Putty Tubing Cutter Tape
Adjustable Wrench
Putty Knife
Channel Locks
Pipe Wrench Silicone Caulk
Measure
Level
Roughing-in Dimensions
4"
7820.400
MODEL
4-1/2"
(114mm)
8"
(203mm)
1-1/4"
O.D. WASTE
FINISHED FLOOR
FINISHED
WALL
OR
SPLASH BACK
1-3/4"
(44mm)
13-3/4"
*
(349mm)
*33-1/2"
(851mm)
11-1/4"
*
(286mm)
SUPPLIES
AS REQ'D
1-1/4" O.D. TAILPIECE
1-3/4"
DIA.
(102mm)
31-1/8"
(791mm)
10-1/8"
(257mm)
(559mm)
SUGGESTED
*
DIMENSIONS
22"
(581mm)
8"
(203mm)
22-7/8"
Vanity Installation
Two people recommended for this
installation
Mount the drain assembly (not included) on
the sink. Be certain to apply a bead of
sealing putty on the underside of the drain
(Part "A") in order to ensure a watertight seal
between the sink and drain. Remove excess
putty after installing the drain on the sink.
Apply a bead of silicone adhesive to the rim
of the vanity. Place the top centered left to
right on the vanity and with the back edge of
the top even with the rear of the vanity. Apply
a bead of silicone along the top back edge of
the vanity top and the wall. Clean up any
excess silicone.
Connect the trap to the drain assembly hand
tight to check alignment. It may be necessary
to cut off part of the tailpiece (area "B") or part
horizontal leg of the trap (area "C").
Connect hot and cold supply lines to the shut
off valves. Tighten trap joints for watertight
assembly.
CARE AND CLEANING
When cleaning your vanity top, wash it with mild, soapy water, rinse
thoroughly with clear water and dry with a soft cloth. Avoid abrasive
detergents, disinfectants, or cleaning products in aerosol cans.
A
C
B
AMERICAN STANDARD ONE-YEAR LIMITED WARRANTY
If inspection of this American Standard plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship, American Standard
will repair or, at its option, exchange the product for a similar model.
This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building
or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other
damage; if it was not installed in accordance with American Standard's instructions; or if it has been modified in a manner inconsistent with the product as shipped by American
Standard.
American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall American
Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of
which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to
you.)
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not
affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request
(including a description of the product model and of the defect) be sent to the following address:
In the United States:
American Standard Inc.
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty information may also be
obtained by calling the following toll free number: (800) 442-1902
In Canada:
American Standard
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: (800) 387-0369
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
730837-100 Rev. A
Loading...