American Standard 7812.295, 7812.002 User Manual
ASSEMBLY & INSTALLATION
INSTRUCTIONS
RETROSPECT® CONSOLE TABLE
7812.002
7812.295
Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years.
To help insure that the installation process will proceed smoothly, please read these instructions carefully before you
begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.
Recommended Tools & Materials
Adjustable Wrench
Channel Locks
Plumbers' Putty or
Caulking
Phillips Screwdriver
Level
0282.008 RETROSPECT® CONSOLE PEDESTAL TOP
8711.000.002 CONSOLE TABLE LEGS (Chrome)
8711.000.295 CONSOLE TABLE LEGS (Satin)
FINISHED WALL
9"
(229mm)
1-3/4" DIA.
STD. DRAIN
OUTLET
13-3/4"
(349mm)
8"
(203mm)
3 Holes
1-3/8" (35mm) Dia.
3-3/8"
(86mm)
15"
(381mm)
19-3/4"
(502mm)
Tape
Measure
Regular Screwdriver
Putty Knife
FINISHED
WALL
Pipe Wrench
Hacksaw
Drill
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2003
11"
(279mm)
7-1/2"
(191mm)
(184mm)
3/8" (10mm) DIA.
SINK ANCHOR
SCREW HOLES
ON 13-3/4" (349mm)
CENTERS
FINISHED
FLOOR
- 1 -
7-1/4"
24"
*
(610mm)
22"
*
(559mm)
22"
(559mm)
27"
(686mm)
8"
(203mm)
1-1/4 O.D.
WASTE
1-1/4" O.D.
TAILPIECE
8-1/8" TO
BOTTOM OF
DRAIN OUTLET
(206mm)
SUPPLIES
AS REQ'D
36"
(914mm)
730757-100 REV. B
1
#3
#2
#1
Run the two front leg sub-assemblies (Item #1) through the
two front holes of the towel bar (Item #2). Do the same with
the two rear leg assemblies (Item #3). Adjust the hex nut at
the end of each rear leg such that 5/8" of thread is exposed.
Turn the unit upside down.
2
Place a middle leg tube
(Item #4) over each
threaded rod. Identify the
shelf support pins at the
inner corners of the Shelf
Support (Item #5). Guide
each threaded rod through
the corners of the shelf
support so that these
support pins are nearer to
you.
#4
#5
3 4
#6
#5
Place a bottom leg tube (Item #5) over each threaded rod
such that the closed end of each is nearer to you. Thread one
hex nut from the kit (Item #6) onto each rod. Lay the unit
down and tighten each of the four legs firmly. Maintain the
5/8" of exposed thread at the top end of the rear legs. Once
again, set the unit upside down.
#8
#7
Thread one decorative foot (Item #7) onto the end of each rod
until the leading end of the rod is recessed with the foot to a
depth of 1/4". Set the unit upright and thread one leveling
trumpet (Item #8) on the top of the rear legs.
Note: To prevent breakage, put the rectangular glass
shelf in place only after the sink and console legs are
completely assembled and the sink has been bolted to
the wall.
Upon completion of console assembly, follow installation
procedure below.
SINK AND CONSOLE TABLE LEG INSTALLATION
1
Note: If replacing an existing sink be certain to shut
off water supply before removing old sink. If installing
in a new bathroom follow rough-in diagram to locate
rough supply, waste lines.
Provide suitable reinforcement behind finished wall for
sink hanger screws. For an installed sink height of
36", center the reinforcement 29" above the floor.
- 2 -
C/L of 2 x 8
Support
and Bracket
30-3/4"
Finished
Floor
730757-100 REV. B
Loading...