American Standard 7502.403, A112.19.3, 7502.103 User Manual
CULINAIRE™ 33" STAINLESS STEEL
KITCHEN SINK
❏ 7502.103 Top Mount, Single Faucet Hole
❏ 7502.403 Top Mount, 4 Faucet Holes
• 18 Gauge Stainless Steel
• 18/10 Chrome Nickel content
• Double bowl design
• Top mount
• Choice of 1 or 4 faucet holes
• One accessory hole
• Mounting clips supplied
Nominal Dimensions:
838 x 559 x 209mm
(33" x 22" x 8-1/4")
❏ 7502.000 Undercounter Mount
• 18 Gauge Stainless Steel
• 18/10 Chrome Nickel content
• Double bowl design
• Undercounter installation
• Mounting clips and cutout template supplied
CULINAIRE™ 33"
DOUBLE BOWL
18 GAUGE STAINLESS STEEL
7502.103 Shown with 4137.100 Culinaire Pull-out
Kitchen Faucet (not included)
Nominal Dimensions:
781 x 470 x 200mm
(30-3/4" x 18-1/2" x 7-7/8")
Bowl sizes:
343mm (13-1/2") wide
410mm (16-1/8") front to back
200mm (7-7/8") deep
Compliance Certications Meets or Exceeds the Following Specications:
• ASME A112.19.3 for Stainless Steel Plumbing
Fixtures
• CSA B45 for Plumbing Fixtures
To Be Specied:
❏ Color: Stainless Steel
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Soap Dispenser: 4503.115
❏ Vinyl Coated Bottom Sink Rack-Sm: 7412.100
* See faucet section for available models
7502.000 Shown with 4233.601 Culinaire
Kitchen Faucet (not included)
SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS
❏ Vinyl Coated Dish Rack-Sm: 7532.100
❏ Wood Cutting Board-Rectangular: 9001.100
❏ Stainless Steel Colander: 8130.100
❏ Hole Cover Plug: 790773-0070A
❏ Top Mount Clip Kit for 1" plus-thick countertop:
790772-0070A
© 2008 AS America Inc.
G3
Revised 2/08
33" (838mm)
16-1/2"
(419mm)
C/L
22"
(559mm)
11"
(279mm)
2-7/8"
(73mm)
3-1/8" (79mm)
3-1/2" (89mm)
CUTOUT AREA
32-1/8" X 21-1/8"
(816 X 562mm)
3-3/4"
DIA. DRAIN
(2 PLACES)
1-3/8"
DIA.
7502.103
4"
(103mm)
4"
(103mm)
4"
(103mm)
1-1/6" DIA.
FINISHED WALL
OR SPLASHBACK
OPTIONAL
8-1/8"
(206mm)
5-3/4"
(146mm)
3/16" (5mm)
7/8" (22mm)
SEALING
COMPOUND
COUNTERTOP
(BY OTHERS)
1-1/2" O.D.
TAILPIECE
(2 PLACES)
36"
(914mm)
SUGGESTED
FINISHED FLOOR
MOUNTING CLIP DETAIL (TYP.)
COUNTERTOP
MTG.
CLIP
ADJ.
SCREW
1-9/16" (40mm)
MAX.
13/16" (21mm)
MIN.
7-3/8"
(187mm)
7-3/8"
(187mm)
30-3/4" (781mm)
15-3/8"
(391mm)
C/L
18-1/2"
(470mm)
8"
(203mm)
CUTOUT AREA
(TYPICAL)
3-3/4"
DIA. DRAIN
(2 PLACES)
7-7/8"
(200mm)
5-3/4"
(146mm)
COUNTERTOP
(BY OTHERS)
1-1/2" O.D.
TAILPIECE
(2 PLACES)
36"
(914mm)
SUGGESTED
FINISHED FLOOR
7-1/2"
(190mm)
7-1/2"
(190mm)
SEALING
COMPOUND
MTG. CLIP
(SEE DETAIL)
MOUNTING CLIP DETAIL (TYP.)
COUNTERTOP
MTG.
CLIP
SCREW
SINK
BRASS
INSERT
1/2" MIN.
(13mm)
FINISHED WALL
OR SPLASHBACK
OPTIONAL
7502.103/403 Top Mount
CULINAIRE™ 33"
DOUBLE BOWL
18 GAUGE STAINLESS STEEL
NOTES:
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME A112.19.3.
These measurements are subject to c hange or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
NOTES:
TEMPLATE PROVIDED WITH MOUNTING KIT FOR UNDER-COUNTER
*
CUTOUT VARIATIONS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME A112.19.3.
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet
© 2008 American Standard Inc.
7502.000 Undercounter Mount
G4
Revised 2/08
Loading...