American Standard 7501.103, 7501.000 User Manual
CULINAIRE™ 25" STAINLESS STEEL
KITCHEN SINK
❏ 7501.103 Top Mount
• 18 Gauge Stainless Steel
• 18/10 Chrome Nickel content
• Single bowl design
• Top mount
• Single faucet hole
• One accessory hole
• Mounting clips supplied
Nominal Dimensions:
635 x 559 x 229mm
(25" x 22" x 9")
❏ 7501.000 Undercounter Mount
• 18 Gauge Stainless Steel
• 18/10 Chrome Nickel content
• Single bowl design
• Undercounter installation
• Mounting clips and cutout template supplied
CULINAIRE™ 25"
SINGLE BOWL
18 GAUGE STAINLESS STEEL
7501.103 Shown with 4137.001 Culinaire Kitchen
Faucet (not included)
Nominal Dimensions:
580 x 516 x 220mm
(22-7/8" x 20-3/4" x 8-5/8")
Bowl sizes:
540mm (21-1/4") wide
476mm (18-3/4") front to back
219mm (8-5/8") deep
Compliance Certications Meets or Exceeds the Following Specications:
• ASME A112.19.3 for Stainless Steel Plumbing
Fixtures
• CSA B45 for Plumbing Fixtures
To Be Specied:
❏ Color: Stainless Steel
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Soap Dispenser: 4503.115
❏ Vinyl Coated Bottom Sink Rack-Lg: 7414.100
7501.000 Shown with 4137.100 Culinaire Pull-out
Kitchen Faucet (not included)
SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS
❏ Vinyl Coated Dish Rack-Lg: 7354.100
❏ Vinyl Coated Dish Rack-Sm: 7352.100
❏ Wood Cutting Board-Rectangular: 9001.100
❏ Hole Cover Plug: 790773-0070A
❏ Top Mount Clip Kit for 1" plus-thick countertop:
790772-0070A
* See faucet section for available models
© 2008 AS America Inc.
G1
Revised 2/08
C/L
12-5/8"
(321mm)
25"
(635mm)
22"
(559mm)
6-3/8"
(162mm)
2-3/4" (70mm)
2-3/4" (70mm)
2-3/4" (70mm)
CUTOUT AREA
24-1/4" X 21-1/8"
(616 X 537mm)
3-3/4"
DIA. DRAIN
1-3/8"
DIA.
1-1/16"
DIA.
FINISHED WALL
OR SPLASHBACK
OPTIONAL
2-3/4" (70mm)
9"
(229mm)
5-3/4"
(146mm)
3/16" (5mm)
7/8" (22mm)
SEALING
COMPOUND
COUNTERTOP
(BY OTHERS)
1-1/2" O.D.
TAILPIECE
36"
(914mm)
SUGGESTED
FINISHED FLOOR
MOUNTING CLIP DETAIL (TYP.)
COUNTERTOP
MTG.
CLIP
ADJ.
SCREW
1-9/16" (40mm)
MAX.
13/16" (21mm)
MIN.
11-7/16"
(291mm)
22-7/8"
(581mm)
20-3/8"
(518mm)
CUTOUT AREA
(TYPICAL)
3-3/4"
DIA. DRAIN
FINISHED WALL
OR SPLASHBACK
OPTIONAL
8-5/8"
(219mm)
5-3/4"
(146mm)
SEALING
COMPOUND
COUNTERTOP
(BY OTHERS)
1-1/2" O.D.
TAILPIECE
36"
(914mm)
SUGGESTED
FINISHED FLOOR
MOUNTING CLIP DETAIL (TYP.)
COUNTERTOP
MTG.
CLIP
SCREW
C/L
5-5/8"
(143mm)
MTG. CLIP
(SEE DETAIL)
SINK
BRASS
INSERT
1/2" MIN.
(13mm)
7501.103 Top Mount
CULINAIRE™ 25"
SINGLE BOWL
18 GAUGE STAINLESS STEEL
NOTES:
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME A112.19.3.
These measurements are subject to c hange or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
NOTES:
TEMPLATE PROVIDED WITH MOUNTING KIT FOR UNDER-COUNTER
*
CUTOUT VARIATIONS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME A112.19.3.
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
© 2008 AS America Inc.
7501.000 Undercounter Mount
G2
Revised 2/08
Loading...