American Standard 7483.295, 7483.002 User Manual

“”

THE

COLLECTION

ASSEMBLY & INSTALLATION INSTRUCTIONS

CONSOLE TABLE

7483.002

7483.295

Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years. To help insure that the installation process will proceed smoothly, please read these instructions carefully before you begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.

Recommended Tools & Materials

Adjustable Wrench

Basin Wrench

Saber Saw

Channel Locks

Plumbers' Putty or Caulking

Pipe Wrench

Putty Knife

Roughing-in Dimensions

FINISHED WALL

0283.000 STANDARD® CONSOLE PEDESTAL TOP

8710.000.002 CONSOLE TABLE LEGS (Chrome)

8710.000.095 CONSOLE TABLE LEGS (Satin)

FINISHED WALL

10-1/4

(260mm)

(330mm)

(813mm)

26-5/8

(676mm)

3/4

(19mm)

(98mm)

3-7/8

(508mm)

10'

Tape Measure

Hacksaw

Regular Screwdriver

Phillips Screwdriver

Product names listed herein are trademarks of American Standard Inc. © American Standard Inc. 2004

Tubing Cutter

Drill

Level

9-1/2

(241mm)

- 1 -

(914mm)

FINISHED

FLOOR

SUPPLIES

1-1/4 O.D.

TAILPIECE

(203mm)

(432mm)

1-1/4 O.D. WASTE

8-1/2

(216mm)

(559mm)

(610mm)

730520-100 Rev. D

1A 1B

6, 7

Remove lower leg support / adjustable foot assembly (items 2 & 3) from accessories box and screw them completely onto the 4 threaded rods (item 5).

Unscrew the 2 front leg trumpets (item

6) and 2 rear leg trumpets (item 7) from the threaded rod (item 5).

Slide Shelf Support (item #1) onto 4 leg subassemblies.

Slide the 4 Upper Legs (item #4) onto the Threaded Rods from the 4 leg subassemblies as shown.

Threaded Rod

Rear

Front

Screw on the 2 Front Leg Trumpets (item #6) and 2 Rear Leg Trumpets (item #7). Make sure the Upper Legs recess into the underside of the Trumpets.

Slide the 2 Towel Bar Assemblies (item #9) over the tops of the Trumpets and secure with the 4 Towel Bar Retaining Nuts (item #10). The retaining nuts can be tightened by hand.

Front

Place the 2 Front Leg Grommets (item #12) over the tops of the 2 Front Leg Trumpets.

NOTE: To prevent breakage, slide the Oval Glass Shelf (item #11) into place

assembled and the lavatory is bolted to the wall.

protective film from glass shelf before final assembly.

CAUTION: Do not use towel bars as handles to move the console table. Lift the console from the upper legs.

After console table is assembled, follow lavatory installation procedure below.

PEDESTAL TOP AND CONSOLE TABLE LEG INSTALLATION

NOTE: If replacing an existing lavatory be certain to shut off water supply before removing old lavatory.

only after the lavatory and Console Legs are completely

Be sure to remove

C/L of 2 x 8 Support and Bracket

Hanger Location

Provide suitable reinforcement behind finished wall for lavatory hanger mounting screws. The desired rim height for the Standard pedestal top is 36". The centerline for the hanger positioning slots should be located at 30-3/4". (Make sure support bottom extends to pedestal top back wall bottom.)

- 2 -

30-3/4"

Finished Floor

730520-100 Rev. D

+ 2 hidden pages