American Standard 7460.100, 7460.200 User Manual

™

ASSEMBLY & INSTALLATION
INSTRUCTIONS

Enfield Console Table

7460.100 With Raised Wood Panels

7460.200 With Cast Grilles

CONSOLE TABLE VANITY TOP-GRANITE RECOMMENDED SINK

7460.100

7460.200

Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years.
To help insure that the installation process will proceed smoothly, please read these instructions carefully before you
begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.
To maintain the beauty of the finish, avoid placing the furniture in direct sunlight, as sunlight causes fading. Also avoid
extreme changes in temperature by arranging furniture away from radiators, heat and air vents, and air conditioning units.
Avoid placing furniture directly under windows.

6860.725 Bakersfield White or

6860.722 Autumn Spray

0740 Enfield

Recommended Tools & Materials

Adjustable Wrench

Basin Wrench

Channel Locks

Plumbers' Putty or
Caulking

Phillips Screwdriver

Regular Screwdriver

Putty Knife

10'

Hacksaw

Pipe Wrench

Tubing Cutter

Drill

Saber Saw

25-1/4

(641mm)

PANELED INSERT

1-1/8" (30mm) THK.

GRANITE SURFACE

12-3/4

*

(324mm)

12-1/4

(811mm)

SATIN SWALLTAIL

LAPPER

Roughing-in Dimensions

8" *

(203mm)

22 REF.

(559mm)

29

(737mm)

8

(203mm)

CAST METAL
DESIGN INSERT

11-1/4

(286mm)

SEALING
COMPOUND

SUPPLIES
AS REQ'D

1-1/4 O.D.

WASTE

1-1/4 O.D.

TAILPIECE

FINISHED

FLOOR

(102mm)

7

(178mm)

4" *

(159mm)

1-1/4

(32mm)

6-1/4

14-1/8

(359mm)

(413mm)

34

(864mm)

C

L

of Faucet **

16-1/4

Tape
Measure

Level

Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2002

- 1 -

25-3/4 REF.

(654mm)

LEG ANCHORING
SCREW HOLES
5/16 (8mm) DIA.
(TYP. 4 PLACES)

752877-100 REV. A

CONSOLE TABLE INSTALLATION

Identify desired location of the console table.
Provide suitable reinforcement required for anchoring the vanity to the wall. Centerline of reinforcement should be 30" up

from the floor (see Figure 1).
Rough in supply lines and waste per rough in dimensions.
Drill at least two 3/8" O.D. anchoring holes through the rear stringer of the console table at 2-1/2" down from the top of

the table (see Figure 2).
Move the vanity into place and level with the adjustable glides on the bottom of the feet. The glides can be adjusted

outward up to 3/8". Anchor it to the wall through the 2 anchoring holes in the rear of the vanity (see Figure 2). Do not
overtighten to prevent cracking the rear stringer.

19-1/4"

C/L of 2 x 6
Reinforcement

489mm

FIGURE 2

2-1/2"
64mm

30"

FIGURE 1

762mm

Finished
Floor

VANITY TOP, SINK, AND FAUCET INSTALLATION

Install the faucet onto the granite top per the manufacturer's instructions.

Two people recommended for this installation

Apply a continuous 1/8" bead of silicone
sealant 1" from the inside edge of the
console. Carefully set the stone top on the
console table. Be sure that the top is
centered on the table.

ADJUSTABLE

GLIDES

(LOCATED

UNDER

EACH FOOT)

3/8" ANCHORING

HOLES IN

REAR STRINGER

MOLDING

GRANITE TOP

SEALANT

Use mineral spirits to remove excess silicone from the console and stone top.

- 2 -

752877-100 REV. A