American Standard 7430.821, 7431.821, 7431.801, 7430.801 User Manual

Instructions

BERWICK™/ BOULEVARD

SPREAD LAVATORY FAUCET
with

Speed Connect™ Drain

Installation

™

7430.801

7430.821

7431.801

7431.821

7430.821

7431.821

Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.

Speed Connect Drain*

• Fewer parts, installs in less time

7430.801

7431.801

Certified to comply with ANSI A112.18.1

M968640 REV.1.1

• Never needs adjustment

• Guaranteed to seal properly the first time, every time.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Recommended tools

Adjustable Wrench Screwdriver Channel Locks

INSTALL FAUCET

1

NOTE: READ STEP #16 BEFORE INSTALLING SPOUT TO CONVERT FROM SWIVEL TO FIXED SPOUT.

Seat SEAL (1) into under side of SPOUT BASE (2).

Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and DRAIN
CABLE ASSEMBLY (8) through the mounting hole of lavatory or
mounting surface. Figure A.

From below, slide DRAIN CABLE ASSEMBLY (8) and FAUCET SUPPLIES (3)
through opening in the SPACER (9) against underside of deck. Figure B.
Note: For thick deck installaitons the SPACER (9) is not required.

From below, push GASKET (7) and RETAINING WASHER (5) onto
MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (6),
pulling faucet to front of sink, so SUPPLIES (3) rests against
mounting hole. Before final tightening, make sure collar on
MOUNTING NUT (6) is seated into RETAINING WASHER (5).

Figure B.

CAUTION

Turn off hot and cold water
supplies before beginning.

Figure A

Tubing Cutter

Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6)
to complete faucet mounting.

9

7

Figure B

5

6

COLLAR ON

MOUNTING NUT

4

1

GROOVE

(FAUCET

BASE)

MOUNTING

SURFACE

2

4

1

3

5

8

VALVE INSTALLATION

2

Place RUBBER RING (9) into DECK ADAPTER (10).

Install LOCKNUT (11) and RUBBER WASHER (12) onto VALVE BODY (13).
From under side of mounting surface, install VALVE BODY (13) through valve
mounting holes. Threads of VALVE BODY (13) should extent at least 5/16
of a inch above mounting surface top. Fig. A. Thread DECK ADAPTER (10)
onto VALVE BODY (13) until snug against internal stop. If necessary, adjust
LOCKNUT (11).

10

9

5/16'' MIN.

10

9

MOUNTING
SURFACE

1

13

Fig. A.

8

VALVE OUTLET SUPPLY CONNECTION

3

Connect Red Banded Hose to Left
Valve and Blue Banded Hose to
Right Valve.

Attach COUPLING NUTS (1) of
SUPPLY HOSES (2) and tighten
making water tight connection.

Important: Loop SUPPLY HOSES (2)
as illustrated so they do not kink.

12

11

13

HOT

1

RED BAND

12

11

13

2

BLUE
BAND

COLD

INSTALL HANDLES

4

Push ADAPTER (1) on VALVE STEM (2). Tighten
STEM SCREW (3) with a flat blade to secure ADAPTER (1).

(Figure A)

Find correct position of HANDLE ASSEMBLY (4, 4a) by adjusting
male teeth on ADAPTER (1) to female teeth in HANDLE (4, 4a).

Thread HANDLE ASSEMBLY (4, 4a) onto DECK
ADAPTER (5) until snug against mounting surface

FLAT BLADE SCREWDRIVER

.

(Figure A)

LEVER HANDLE CROSS HANDLE

4a4

THREAD ON

TO DECK

ADAPTER

1

1

3

2

5

M968640 REV.1.1

2

POP-UP DRAIN

5

Fig. A. Fig. B.

Remove CLEAR PLASTIC COVER (1).

Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).

Tighten TAILPIECE (4) on DRAIN BODY before
installing DRAIN BODY.

REMOVE FLANGE

6

Thread FLANGE (1) counter-clockwise and remove
FLANGE (1) and FOAM GASKET (2) from drain
body.

Fig. A.

Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3).

Fig. B.

Fig. B.

1

3

2

Fig. A. Fig. B.

1

2

4

3

DRAIN
BODY

4

INSTALL DRAIN FROM

7

BELOW FIXTURE

From under side of SINK
install DRAIN BODY (1) up
through drain outlet.

Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the SINK.

Install FOAM GASKET (3) and
FLANGE (4) onto drain body
from above SINK and tighten
FLANGE (4) firmly.

FLANGE GASKET AND POP-UP KNOB

9

Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.

POP-UP KNOB (1) must be fully down. Fig. B.

4

3

REAR OF SINK

DRAIN
OUTLET

1

2

Fig. A.

WHITE FOAM
GASKET
NOT VISIBLE

TIGHTEN LOCKNUT

8

Tighten LOCKNUT (1) firmly with Adjustable
Wrench or Channel Locks.

1

DRAIN
FLANGE

DOWN

1

M968640 REV.1.1

3