American Standard 7402, 5401, 7490, 5402, 5400 User Manual
...
Installation
Instructions
5400 SERIES
5401 SERIES
5402 SERIES
HERITAGE SERIES
4" CENTERSET LAVATORY
AND BAR SINK FAUCETS
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
5401 SERIES
CENTERSET
W/POP-UP
7400 SERIES
7401 SERIES
7402 SERIES
7490 SERIES
Certified to comply with ANSI A112.18.1M
U.S. PATENT NOS. 5,819,789; 4,294,289
34063M-B
HANDLE
SCREW
7401 SERIES
CENTERSET WITH
GOOSENECK SPOUT
7490 SERIES
BAR SINK WITH
SWING SPOUT
BODY
SHANK
RUBBER
WASHER
BRASS
WASHER
LOCKNUT
COUPLING
NUT
POP-UP
ROD
THUMBSCREW
EXTENSION
CARTRIDGE
AERATOR
STOPPER
DRAIN
FLANGE
GASKET
WASHER
NUT
Printed in Mexico
CLIP
PIVOT
TAILPIECE
DRAIN
BODY
ROD
1
Turn off hot and cold water supplies before beginning.
Apply a bead of PUTTY along the edge of the underside of the BODY and insert faucet
SHANKS through holes of SINK.
Assemble RUBBER and BRASS WASHERS, and LOCKNUTS from underside of SINK.
Drop UPPER LIFT ROD through hole in BODY (models 5401 & 7401 only), align BODY
as far forward as possible and secure position by tightening LOCKNUTS. (Plastic LOCKNUTS
on model 7490 are tightened by hand.)
Connect the HOT water supply to the left SHANK and the COLD water supply to the right
SHANK using sealant, appropriate connectors, and COUPLING NUTS.
Refer to separate "Instruction Sheet" for assembly of handles.
DRAIN ASSEMBLY
2
(Models 5402 and 7402 only)
Apply a bead of PUTTY around underside
of DRAIN PLUG flange. Insert DRAIN
PLUG into SINK drain hole.
Hold DRAIN PLUG to prevent turning
and assemble GASKET, WASHER, and
LOCKNUT, from underneath sink.
Insert threaded end of TAILPIECE
into lower end of DRAIN PLUG.
Connect other end to trap.
CAUTION
PUTTY
RUBBER
GASKET
LOCKNUT
TAIL
PIECE
FLANGE
SINK
DRAIN
PLUG
WASHER
SINK
HANDLE SCREW
UPPER LIFT ROD
BODY
SHANK
PUTTY
1/2" O.D. SLIP
RUBBER WASHER
BRASS WASHER
LOCKNUT
COLD
HOT
COUPLING NUT
INSTALL POP-UP DRAIN
3
(Models 5401 and 7401 only)
Push TAILPIECE down into TRAP (threaded end up).
Thread LOCKNUT, WASHER and GASKET onto
DRAIN BODY.
Apply a bead of PUTTY to underside of FLANGE.
Feed DRAIN BODY up through SINK and thread
FLANGE fully onto BODY.
Tighten LOCKNUT firmly, keeping the PIVOT ROD
pointed towards the back of the SINK.
Drop STOPPER into DRAIN BODY.
Pull TAILPIECE up and thread tightly
into DRAIN BODY.
Position EXTENSION ROD onto POP-UP ROD and
tighten THUMBSCREW.
TEST INSTALLED FAUCET
4
Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
SERVICE
5
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90° and replace.
Replace SPRING CLIP.
Replace ADAPTER, HANDLE, SCREW, and INSERT.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 223-0068
Weekdays 8:00 a.m. to 4:00 p.m. Eastern Time
STOP
WASHER
FLANGE
SINK
LOCKNUT
90°
STOPPER
Remove one end of CLIP from PIVOT ROD by
squeezing ends together while sliding.
Insert PIVOT ROD into second or third hole in
EXTENSION and reassemble CLIP. (EXTENSION
may need to be bent.)
PUTTY
Adjust STOPPER height by repositioning EXTENSION
and tightening THUMBSCREW.
GASKET
WASHER
CLIP
PIVOT
ROD
TAILPIECE
TRAP
Operate both handles to flush water lines thoroughly. Check
spout mounting and hose connections for leaks.
Operate LIFT ROD and check DRAIN for leaks.
Turn handles into OFF position and replace AERATOR.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90°.
SPRING
CLIP
Plastic SCREEN in CARTRIDGE may accumulate
dirt causing reduced water flow. To clean, first
turn off hot and cold water supplies, then:
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Unscrew CARTRIDGE with wrench.
Thoroughly rinse plastic SCREEN at
base of CARTRIDGE.
Replace CARTRIDGE until flange is
tight against valve body.
Turn valves OFF.
Replace ADAPTER, HANDLE, SCREW,
and INSERT.
Product names listed herein are trademarks of American Standard Inc.
C
American Standard Inc. 1999
THUMBSCREW
EXTENSION
ROD
DRAIN
BODY
TRAP
TAILPIECE
POP-UP ROD
EXTENSION
ROD
CARTRIDGE
SCREEN
CLIP
PIVOT
ROD
34063M-B
Loading...