American Standard 7274.521VR, 7274.521, 7274.515, 7274.525 User Manual
Installation Instructions
[
]
[
]
[
]
]
"
[
]
"
[
]
"
]
N
]
D
]
N
]
D
]
(
C)
]
]
]
]
"
]
"
]
]
]
"
]
N
]
/16"
]
]
3/8" NPT MALE
1
R
]
]
"
.
]
]
"
]
UM
SS
]
"
[
]
]
INDEXED 'AIR', 'GAS', VAC.
INDEXED 'AIR', 'GAS', VAC.
COMBO VALVE AND TURRET FITTINGS
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these instructions carefully
before you begin.
7274.521
7274.521VR
7274.511
7274.511VR
ROUGHING-IN DIMENSIONS
7274.525
INDEXED AS REQUIRED
AIR, GAS, VA
51mm
3/8" NPT FEMALE
305mm
"
51mm
5-3/8"PE
-1/8" CLOSE
1-1/8
[29mm
137mm
130mm
3-7/8
98mm
3-1/4
83mm
7274.521
7274.521VR
INDEXED 'AIR' OR 'GAS'
2-3/8" [60mm
WARE THICK
7274.5257274.515
27mm
3-1/8
79mm
"
1mm
mm
7mm
M968486
51mm
PIN LENGTH
3/8"[10mm
1/4" DIA. [6mm
7274.51
7274.511V
3/8" NPT FEMALE
1-1/8
29mm
2-3/8" [60mm
MAXIM
WARE THICKNE
3-1/4
83mm
51mm
1/16
7mm
17mm
11/16"
DIA
3-7/8
98mm
PIN LENGTH
3/8"
10mm
1/4" DIA. [6mm
7274.515
3/8" NPT FEMALE
60mm
"
51mm
5-3/8"PE
137mm
5-1/8" CLOSE
130mm
1-1/8
29mm
TOOLS AND SUPPLIES REQUIRED
Y
UT
S
R
0A
"
H
R
N
T
Y
OR
N
T
Y
Teflon Tape
Channel Locks
COMBO VALVE TURRET FITTINGS
1
AND VANDAL RESISTANT
IMPORTANT: FLUSH ALL SUPPLY LINES PRIOR TO FITTING INSTALLATION.
Adjustable Wrench
Drill
For vandal resistant fitting only, a pin hole will be need to be drilled into the deck offset from the mounting shank hole.
Note: For vandal resistant models it is important to obtain the rough-in drawing for the particular model. The
drawing illustrates exact size and positioning of the offset hole. Drill a 5/16" [8mm] dia. hole 1/2" [13mm] deep
in mounting surface, per roughing-in dimensions for vandal resistant pin.
Note: 7274.515/525 require inlet shank M962323-0070A for installation
and must be ordered separately.
Apply
putty to underside of turret body to assure a good seal and level fit.
If installing a vandal resistant fitting, align pin with pin hole in mounting surface.
Place body shank through hole in deck and assemble steel washer and
lock nut. Tighten securely.
Pipe to correct service to complete installation.
After installation is complete turn service on and check all connections
for leaks.
Plumbers' Putty or
Caulking
TURRE
BOD
PUTT
M962323-007
3/8" NPT X 4-3/4
INLET SHANK WIT
LOCKNUT & WASHE
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR
WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH,
ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A
COARSE SURFACE.
VANDAL RESISTANT PI
N VANDAL RESISTAN
FITTINGS ONL
FFSET HOLE F
VANDAL RESISTANT PI
TEEL WASHE
LOCK N
For toll-free information and answers to your questions, call:
1-800-387-0369 (TORONTO 1-905-306-1093)
Product names listed herein are trademarks of American Standard Inc.
HOTLINE FOR HELP
1 (800) 442-1902
8:00 to 7:00 p.m. Eastern Time
Weekdays
CANADA
©American Standard Inc. 2004
M968486
Loading...