American Standard 7242EC User Manual
RONDO ELITE™
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
RONDO ELITE™ WHIRLPOOL
Comfortable two person oval design with dual
back support positions and factory installed
grab bar
❏ 7242E (specify White 020, Bone 021, or
Linen 222)
• Acrylic with fiberglass reinforcement
• 2.0 HP self-draining pump/motor
with dry run seal
• Ten multi-directional and flow adjustable jets
including:
Two high performance Ideal-flow™ Jets
Eight interchangeable Flex-jets™
• Three silent air volume controls
• Deck-mounted On/Off control
• Complete factory installed and tested
whirlpool system
❏ 7242EC (specify White 020, Bone 021, or
Linen 222)
• Same as above with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®
Nominal Dimensions: 1816 x 1067 x 546mm
(71-1/2” x 42” x 21-1/2")
© 2003 American Standard Inc.
HD-006
SPS 7242E
Revised 6/03
Components Needed:
❏ Bath Filler*: (specify finish)
❏ Bath Drain: BATH-DRAIN
(specify Chrome 002, Polished Brass 099,
or Satin 295)
Custom Accessories Available:
❏ Pulse Jet Kit: PULSE-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
❏ Soft Jet Kit: SOFT-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
❏ E-Z-Install™ Whirlpool Heater - EZHEAT-100
NOTE: Roughing-in dimensions and product specifications shown on reverse side of page.
Compliance Certifications Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
* See American Standard Faucet Selector
NOTE: E-Z-Install™ Whirlpool Heater is designed to
maintain water temperature during operation. It will not
heat cold water to desired bathing temperature.
RONDO ELITE™
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR
PENINSULA TYPE INSTALLATION. SUPPORT OF BATH BY INTEGRAL FEET. NO ADDITIONAL
SUPPORT REQUIRED. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL
INFORMATION.
CUTOUT TEMPLATE PROVIDED IN SHIPPING BOX, MAY BE REQUESTED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
FITTINGS AND TWIST GRAB BAR NO. 750565-000 NOT INCLUDED, MUST BE ORDERED
SEPARATELY.
IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY
HOLES: CHECK FOR
INTERFERENCE WITH CIRCULATING SYSTEM PIPING, DRAIN OVERFLOW, AND APRON
INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances
established by ANSI Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided leaflet.
●
●
■
●
RECOMMENDED FITTING
LOCATION 64 X 279mm
267mm
(10-1/2)
(2-1/2 X 11)
165mm
(6-1/2)
1816mm
(71-1/2)
908mm
(35-3/4)
76mm
(3)
229 X 305mm
(9 X 12)
CUTOUT
C/L OF DRAIN
38mm
(1-1/2)
83mm
(3-1/4)
PUMP
1067mm
(42)
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
OVERFLOW
95mm
(3-3/4)
C/L OF
GENERAL SPECIFICATIONS FOR 7242E WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
PUMP
ON/OFF
SWITCH
▲
OUTLINE OF
CUTOUT
SAFETY HEATER
REMOVABLE BLANK
495mm
(19-1/2)
ROUGH
38 mm (1-1/2)
TAILPIECE
71-1/2 x 42 x 21-1/2 In (1816 x 1067 x 546mm)
45 x 25 In. (1143 x 635mm)
60 x 30 In. (1524 x 762mm)
39 Lbs./Sq.Ft. (191 Kgs./Sq.m)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
FLOOR
INTEGRAL
FEET
94 Lbs.(43 Kg.)
818 Lbs.(371 Kg.)
14-7/8 In (378mm.)
2.1 HP, 14.4 AMPS,120.
■
LEVELING STRINGER
NOT FOR SUPPORT
51mm
(2)
546mm
(21-1/2)
87 Gal. (330 L)
67 Gal. (254 L)
30.3
58.7
Loading...