American Standard 7236EC, 7236E User Manual

VIRTUOSO ELITE™

WHIRLPOOLS BY AMERICAN STANDARD

HIGH GLOSS ACRYLIC

VIRTUOSO ELITE™ WHIRLPOOL

Comfortable two person design with dual back support positions and factory installed grab bar

❏ 7236E (specify White 020, Bone 021, or

Linen 222)

• Acrylic with fiberglass reinforcement

• 2.0 HP self-draining pump/motor

with dry run seal

• Ten multi-directional and flow adjustable jets including: Two high performance Ideal-flow™ Jets Eight interchangeable Flex-jets™

• Three silent air volume controls

• Deck-mounted On/Off control

• Complete factory installed and tested

whirlpool system

❏ 7236EC (specify White 020, Bone 021, or

Linen 222)

• Same as above with the StayClean™ whirlpool system featuring Antimicrobial AlphaSan®

Nominal Dimensions: 72” x 36” x 21-1/4" (1829 x 914 x 540mm)

HD-007

SPS 7236E

Revised 6/03

Compliance Certifications -

Meets or Exceeds the Following Specifications:

• Underwriters Laboratories - Hydromassage Bathtubs UL 1795

• ASME A112.19.7M for Whirlpool Appliances

• ANSI Z124.1 for Plastic Bathtubs

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

Components Needed:

❏ Bath Filler*: (specify finish) ❏ Bath Drain: BATH-DRAIN

(specify Chrome 002, Polished Brass 099,

or Satin 295)

Custom Accessories Available:

❏ Pulse Jet Kit: PULSE-JET (two per kit,

specify White 020, Bone 021, or Linen 222)

❏ Soft Jet Kit: SOFT-JET (two per kit, specify

White 020, Bone 021, or Linen 222)

❏ Six Foot Apron: 6FT-APRON (specify White

020, Bone 021, or Linen 222)

❏ E-Z-Install™ Whirlpool Heater - EZHEAT-100 ❏ Tile Bead Kit: TILE-BEAD

* See American Standard Faucet Selector

NOTE: Roughing-in dimensions and product specifications shown on reverse side of page.

NOTE: E-Z-Install™ Whirlpool Heater is designed to maintain water temperature during operation. It will not heat cold water to desired bathing temperature.

VIRTUOSO ELITE™

WHIRLPOOLS BY AMERICAN STANDARD

HIGH GLOSS ACRYLIC

●

■

NOTES:

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.

REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL, DECK MOUNTED SPOUT AND INTEGRATED BATH FILLER FOR ADDITIONAL INFORMATION.

OPTIONAL 3-WALL TILING BEAD KIT No. TILE-BEAD AND APRON No. 6FT-APRON MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS. IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR

INTERFERENCE WITH CIRCULATING SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established

by ANSI Standard Z124.1 These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.

914mm

(36)

(70-1/2 X 34-1/2)

1791mm X 876mm

OUTLINE OF CUTOUT

279mm

(11)

C/L OF

OVERFLOW

76mm

(3)

44mm

(1-3/4)

C/L OF

DRAIN

914mm

(36)

IN-LINE HEATER REMOVABLE BLANK

102mm (4)

1829mm

(72)

PUMP

178mm X 356mm (7 x 14) CUTOUT

470mm

(18-1/2)

RECOMMENDED FITTING LOCATION 64 X 279mm (2-1/2 X 11)

489mm (19-1/4)

LEVELING STRINGER NOT FOR SUPPORT

ON/ OFF

SWITCH

51mm (2)

19mm (3/4) TYP.

PROVIDE ACCESS

ON ALL INSTALLATIONS

TO PUMP FOR SERVICE

540mm

21-1/4

89mm

(3-1/2)

1-1/2 N.P.T. THREAD

1-1/2 O.D. TAILPIECE

INTEGRAL FEET

ROUGH FLOOR

GENERAL SPECIFICATIONS FOR 7236E WHIRLPOOL

INSTALLED SIZE WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW WHIRLPOOL MIN. OPERATING VOL. BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS.

CUBE (FT3)

PUMP

WHIRLPOOL ELECTRICAL SPECIFICATIONS

72 x 36 x 21-1/4 In. (1829 x 914 x 540mm)

66 x 30-1/2 In. (1676 x 775mm)

42 Lbs./Sq.Ft. (204 Kgs./Sq.m)

101 Lbs. (45 Kg.)

751 Lbs. (338 Kg.)

78 Gal. (296 L)

46 x 18 In. (1168 x 457mm)

2.1 HP,14.4 AMPS,120V.

69 Gal. (262 L)

15-3/4 In.(400mm)

25.6

49.4