American Standard 7193.001, Lakeland 33, 7193.803, 7193.000, 7193.805 User Manual
...
LAKELAND™ 33" LARGE SINGLE BOWL
KITCHEN SINK
• Americast® brand engineered material
• Single bowl design
• Titanium enamel - heat resistant up to 1000°
• Acid-resisting glossy porcelain nish
• Top mount or undercounter installation
• Silicone sealant supplied
• Available in 0, 1, 3, 4 or 5 faucet
hole conguration
• Customized Hole Punching Available
(See Holes page G56)
Top Mount/Undercounter:
❏ 7193.000 No Holes
❏ 7193.001 1 Center Hole
❏ 7193.803 3 Holes
❏ 7193.804 4 Holes
❏ 7193.805 5 Holes
LAKELAND™ 33"
LARGE SINGLE BOWL SINK
Shown with 4114.100 Lakeland Pull-Out
Kitchen Faucet
AMERICAST
®
Undercounter Installation Order:
❏ 791123-100 Mounting Kit (consists of
cut-out templates and mounting clips)
Nominal Dimensions:
838 x 559 x 241mm
(33" x 22" x 9-1/2")
Bowl sizes:
679mm (26-3/4") wide
413mm (16-1/4") front to back
229mm (9") deep
Compliance Certications Meets or Exceeds the Following Specications:
• ASME A112.19.4M for Americast Plumbing Fixtures
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
To Be Specied:
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Trap:
Optional Accessories:
❏ Basin: 8193.300.365
❏ Bottom Sink Rack: 8193.120.075
❏ Bamboo Cutting Board: 8193.200.090
❏ Dish Rack with Two Utensil Holders and
Colander Kit: 8193.400.075
❏ Under Cabinet Storage: 8193.140.075
* See faucet section for available models
SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS
© 2008 AS America Inc.
G41
Revised 2/08
7193.001/803/4/5 Top Mount
FINI SHED FLOOR
36" ( 914mm )
TO FINISHED
FLOOR (OPTIONAL)
COUN TERTO P
BY O THERS
SEAL ING
COMP OUND
719 3.804
(4 H OLES)
FINI SHED WALL
OR S PLASH BACK
7193 .805
(5 H OLES)
1-1/ 2"
(38m m)
RAD. TYP.
CUTO UT
NOTE
SPRA Y
H C
*
1-1/ 2" O.D . TAIL PIECE
1/2"
(13m m)
5-3/ 4"
(146 mm)
9"
(229 mm)
2" (5 1mm) OPTION AL
33"
(838 mm)
8-1/ 8"
(206 mm)
2-1/ 8"
(54m m)
16-1 /2"
(419 mm)
8-3/ 8"
(213 mm)
22"
(559 mm)
3-1/ 2"
(89m m)
DIA.
1-1/ 2" (38 mm)
DIA. HOLE S TYP.
4"
(102 mm)4"(102 mm)4"(102 mm)4"(102 mm)
DETA IL OF MOUNT ING CL IP
(KIT No.7 91123- 100)
BRAS S
INSE RT
13mm
(1/2 )
MIN.
REFE R TO INSTRU CTIONS
PROV IDED WITH K IT FOR
ADDI TIONA L INFO RMATIO N
CLIP
MACH .
SCRE W
SINK
FINI SHED FLOOR
COUN TERTO P
BY O THERS
SEAL ING
COMP OUND
719 3.804
(4 H OLES)
FINI SHED WALL
OR S PLASH BACK
7193 .805
(5 H OLES)
CUTO UT
NOTE
SPRA Y
*
H C
MOUN TING CLIP
(SEE DETA IL)
36" ( 914mm )
TO FINISHED
FLOOR (OPTIONAL)
1-1/ 2"
(38m m)
RAD. TYP.
1-1/ 2" O.D . TAIL PIECE
1/2"
(13m m)
5-3/ 4"
(146 mm)
2" (5 1mm) OPTION AL
33"
(838 mm)
8-1/ 8"
(206 mm)
2-1/ 8"
(54m m)
16-1 /2"
(419 mm)
8-3/ 8"
(213 mm)
22"
(559 mm)
3-1/ 2"
(89m m)
DIA.
1-1/ 2" (38 mm)
DIA. HOLE S TYP.
4"
(102 mm)4"(102 mm)4"(102 mm)4"(102 mm)
9-1/ 2"
(241 mm)
LAKELAND™ 33"
LARGE SINGLE BOWL SINK
AMERICAST
NOTES:
COUNTERTOP CUTOUT for NEW INSTALLATIONS
*
756mm X 527mm with 25mm Radius
(29-3/4" X 20-3/4" WITH 1" RADIUS)
COUNTERTOP CUTOUT for REPL ACEMENT INSTALLATIONS
*
756mm to 806mm X 527mm with 25mm Radius
(29-3/4" to 31-3/4" X 20-3/4" WITH 1" RADIUS)
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to c hange or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
®
NOTES:
●
Wood - 19mm (3/4")
Marble and Solid Surface - 12mm (1/2")
*
UNDERCOUNTER, INSTALLATION AND COUNTERTOP CUTOUT.
FITTINGS AND UNDERCOUNTER MOUNTING KIT NOT INCLUDED
AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ASME Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
© 2008 AS America Inc.
Recommended minimum counter top thickness:
TEMPLATE PROVIDED WITH MOUNTING KIT 791123-100 FOR
7193.001/803/4/5 Undercounter Mount
G42
Revised 2/08
Loading...