American Standard 7193 User Manual
®
™
Installation
Instructions
LAKELAND™ KITCHEN SINKS
SERIES 7193
Thank you for selecting American-Standard...the benchmark of fine quality
for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
AMERICAST BRAND
SELF RIMMING
Certified to comply with ANSI A112.19.4.M
U.S. Patent No. 4,664,982
Other patents pending.
CAN/C.S.A. B-45
Observe local plumbing and building codes.
BEFORE YOU BEGIN...
Unpack new sink and inspect carefully for damage.
Replace the sink in its original packing carton to
protect it until you are ready to begin installation.
Recommended Tools & Materials
Silicone Sealant
Putty Knife
Pipe Wrench
Channel Locks
Phillips Screwdriver
Regular Screwdriver
Adjustable Wrench
COUNTERTOP CUTOUT FOR
NEW INSTALLATIONS
33"
(838mm)
22"
(559mm)
5/8"
(16mm)
LAKELAND SINGLE BOWL
MODEL 7193 SELF RIMMING
COUNTERTOP CUTOUT FOR
REPLACEMENT INSTALLATIONS
Drill
Basin Wrench
Saber Saw
Tubing Cutter
Tape Measure
Hacksaw
Mineral Spirits
1" R (25mm) TYP.
1-5/8" (16mm)
SINK
OUTLINE
CUTTING LINE
Refer to American Standard roughing-in information for
specific dimensions for each model.
CUTOUT DIMENSIONS FOR SINKS:
Below are the dimensions needed to determine the cutout size for your
installation. Select the correct diagram for your application and refer to the
instructions below.
Locate and mark center lines of sink on countertop.
Provide proper clearance under the countertop for the faucet supply lines and
the structural parts of the cabinet.
By using the diagrams below and measuring your sink, draw the outline of
the sink onto the countertop. This is not the cutting outline.
Refer to the diagram for your sink and draw a line the required distance in
from the sink outline. Cut on this line.
COUNTERTOP CUTOUT FOR
UNDERCOUNTER INSTALLATIONS
27-3/8"
(695mm)
CUTOUT
16-7/8"
(429mm)
COUNTERTOP MOUNTED FAUCET
MODEL 7193 UNDER COUNTER MOUNT
LAKELAND SINGLE BOWL
2-5/16" R (19mm) TYP.
SUPPORT
CLIPS
29-1/2"
(749mm)
CUTOUT
3/4" R (19mm) TYP.
SUPPORT
CLIPS
22"
(559mm)
33"
(838mm)
1" R (25mm) TYP.
5/8"
(16mm)
LAKELAND SINGLE BOWL
MODEL 7193 SELF RIMMING
CUTTING LINE
5/8" to 1-5/8"
(16 to 41mm)
SINK
OUTLINE
20-1/2"
(521mm)
SINK MOUNTED FAUCET
MODEL 7193 UNDER COUNTER MOUNT
LAKELAND SINGLE BOWL
CAUTION:
1. Recommended Minimum Countertop Thickness Wood 19mm (3/4") Marble and Solid Surface 12mm (1/2")
2. Prior to cutting countertop ensure that the faucet shank has sufficient length to attach the mounting nut after
the shank goes through both the countertop and the sink deck. The deck is 10mm (3/8") thick.
NOTE: Undercounter Installations of sinks should be done by trained and experienced installers due to the materials (such
as marble, hard synthetics, etc.). Contact your countertop distributor for best method of cutting the opening.
IMPORTANT: DIMENSION OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN
THE RANGE OF TOLERANCES ESTABLISHED BY A.N.S.I. AND C.S.A. STANDARDS.
©AMERICAN STANDARD INC. 2005
791393-100 Rev. A
INSTRUCTIONS FOR COUNTERTOP MOUNTING.
AFTER THE CUTOUT IS DRAWN...
1
Perimeter
of sink
Cutout
Drill a clearance hole inside the cutout line
as marked on the countertop.
2
Perimeter
of sink
Cutout
Cut opening on cut line inside the perimeter of sink.
Note - Formica countertop installation only is
illustrated. Contact your countertop distributor for the
best method of cutting other materials such as marble,
hard synthetics, etc.
4
Cutout
Masking
tape
outline
1/8"
Remove sink and apply a masking tape
outline 1/8" outside traced outline as a
guide for application of silicone sealant.
5
Apply a generous portion of silicone sealant inside line traced
on countertop. Carefully lower sink into place and press down
firmly. Use guidelines for proper positioning. Using water to
dampen your finger, remove excess sealant for a smooth even
line. Apply additional sealant if necessary to provide a uniform
bead from the rim of sink to the masking tape line as shown.
Carefully remove tape. Dampen finger and run it slightly
the sealant to remove any high spots. Use mineral spirits to
remove excess silicone from countertop and sink.
Silicone
Masking
Tape
NOTE:
Silicone must be removed within 10 minutes of application
or a permanent residue may remain on the surfaces.
Sealant
Sink
outline
Sink
over
3
7
Countertop
Sink
Surface
Mount the faucet and drain assembly
on the sink or countertop following
the manufacturer's instructions.
B
A
Trap
Single Bowl
6
Countertop
Connect supply lines to faucet finger tight, and
carefully bend to engage with the supply
stops.Tighten connections to faucet for secure seal.
Connect drain assembly hand tight to check alignment.
It may be necessary to cut off part of the tailpiece (area
"A") or part of the horizontal leg of the trap (area "B").
Secure joint for watertight assembly.
Sink
Surface
791393-100 Rev. A
2
Loading...