American Standard ASTM E162, 7185.001, 7185.803 User Manual

SILHOUETTE™ 18" ISLAND SINK

• Americast® brand engineered material

• Single bowl design

• Titanium enamel - heat resistant up to 1000°

• Acid-resisting glossy porcelain nish

• Top mount or undercounter installation

• Silicone sealant supplied

• Available in 1 or 3 faucet hole conguration

• Customized hole punchings available (see page G56)

Top Mount/Undercounter:

❏ 7185.001 Center hole only ❏ 7185.803 3 hole

Under Counter Installation Order:

❏ 791326-100 Mounting Kit (consists of

cut-out templates and mounting clips)

SILHOUETTE™ 18"

ISLAND SINK

AMERICAST

Top Mount Installation (faucet not included)

Nominal Dimensions:

457 x 457 x 216mm (18" x 18" x 8-1/2")

Bowl sizes:

375mm (14-3/4") wide 375mm (14-3/4") front to back 203mm (8") deep

Compliance Certications Meets or Exceeds the Following Specications:

• ASME A112.19.4M for Americast Plumbing Fixtures

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

To Be Specied:

❏ Color: ❏ Faucet*: ❏ Faucet Finish: ❏ Basket Strainer: 4331.013 ❏ Soap Dispenser: 4503.115, Color: ❏ Trap:

Optional Accessories:

❏ Small Wood Cutting Board: 9000.185 ❏ Colander for Cutting Board: 8102.100, Color:

Undercounter Mount Installation

(faucet not included)

SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS

* See faucet section for available models

G37

Revised 2/08

7185.803/823 Top Mount

C/L

FIN ISHED WALL OR SPLASH BACK

*C UTOUT NOTE

SEA LING C OMPOU ND

FIN ISHED FLOOR

COU NTERTO P

(BY OTHER S)

1-1 /2" O.D . TAI LPIECE

36" (914mm )

SUG GESTED

1/2 " (13 mm)

5-3 /4"

(14 6mm)

9-1 /8"

(23 2mm)

18"

(45 7mm)

18"

(45 7mm)

(22 9mm)

3-1 /2"

(89 mm)

DIA .

1-1 /2" (38 mm) DIA . HOLE S TYP .

2" ( 51mm)

OPT IONAL

7-3 /8"

(18 7mm)

2" (51 mm)

4-5 /8" (11 7mm)

2-5 /8"

(67 mm)

C/L

FINI SHED WALL OR S PLASH BACK

CUTO UT NO TE

COUN TERTO P (BY OTHER S)

SEAL ING C OMPOUN D

FINI SHED FLOOR

DETAI L OF MOUNTI NG CL IP

(KIT No.79 1003-1 00)

BRASS INSE RT

1/2" ( 13mm) MIN.

REFER TO INSTRUCTIONS

PROVIDED WITH KIT FOR

ADDITIONAL INFORMATION

CLIP MACH. SCREW

SINK

MOUN TING CLIP

(SEE DETA IL)

18"

(457 mm)

1-1/ 2" (38 mm) DIA. HOLE S TYP.

2" (5 1mm)

OPTI ONAL

7-3/ 8"

(187 mm)

2" (5 1mm)

4-5/ 8" (117 mm)

2-5/ 8"

(67m m)

18"

(457 mm)

(229 mm)

3-1/ 2"

(89m m)

DIA.

1-1/ 2"

(38m m)

DIA.

1-1/ 2" O.D . TAIL PIECE

36" ( 914mm )

SUGG ESTED

5-3/ 4"

(146 mm)

(229 mm)

SILHOUETTE™ 18"

ISLAND SINK

AMERICAST

NOTES:

TOP MOUNT (7185.803): COUNTERTOP CUTOUT

425mm x 425mm WITH 25mm RADIUS (16-3/4 X 16-3/4 WITH 1" RAD.) AT CORNERS.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ASME Standard A112.19.4 These measurements are subject to c hange or cancellation. No responsibility is assumed for use of superseded or voided leaet.

NOTES:

TEMPLATE PROVIDED WITH MOUNTING KIT 791326-100 FOR

EXPOSED FAUCET DECK OR UNDERCOUNTER FAUCET DECK COUNTERTOP CUTOUT VARIATIONS.

FITTINGS AND UNDERCOUNTER MOUNTING KIT NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ASME Standard A112.19.4 These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaet.

Undercounter Mount

G38

Revised 2/08