American Standard 7183.805, 7183.804, 7183.803, 7183.801 User Manual

SILHOUETTE™ TRIPLE BOWL KITCHEN SINK

• Americast® brand engineered material

• Triple bowl design

• Titanium enamel - heat resistant up to 1000°

• Acid Resisting Glossy Porcelain nish

• Top mount or undercounter installation

• Silicone sealant supplied

• Available in 1, 3, 4, or 5 faucet hole conguration

• Customized hole punchings available (see page G56)

Top Mount/Undercounter:

❏ 7183.001 Center hole only ❏ 7183.803 3 hole ❏ 7183.804 4 hole ❏ 7183.805 5 hole

Undercounter Installation Order:

❏ 791239-100 Mounting Kit (consists of

cut-out templates and mounting clips)

SILHOUETTE™

TRIPLE BOWL SINK

Top Mount Installation

AMERICAST

Nominal Dimensions:

1054 x 559 x 241mm (41-1/2" x 22" x 9-1/2")

Bowl sizes: Right Hand: 359mm (14-1/8") wide 413mm (16-1/4") front to back 229mm (9") deep Center: 91mm (7-1/2") wide 413mm (16-1/4") front to back 178mm (7") deep Left Hand: 359mm (14-1/8") wide 476mm (18-3/4") front to back 229mm (9") deep

Compliance Certications Meets or Exceeds the Following Specications:

• ASME A112.19.4M for Americast Plumbing Fixtures

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS

Undercounter Mount Installation

To Be Specied:

❏ Color (specify color): ❏ Faucet* (specify nish): ❏ Basket Strainer: 4331.013 ❏ Soap Dispenser: 4503.115, (specify color): ❏ Traps:

Optional Accessories:

❏ Large Wood Cutting Board: 9000.250 ❏ Small Wood Cutting Board: 9000.185 ❏ Colander for Cutting Board: 8102.100, Color: ❏ Large Colander: 8103.100, Color: ❏ Web Cover: 8106.100, Color: ❏ Bottom Sink Rack (Left): 7405.100, Color: ❏ Bottom Sink Rack (Right): 7406.100, Color:

* See faucet section for available models

G17

Revised 2/08

7183.803/804/805 Top Mount

8-5/ 8"

(219 mm)

5-3/ 4"

(146 mm)

(203 mm)

1-1/ 2 O.D . TAIL PIECE

1-1/ 2" O.D . TAIL PIECE

COUP LING NUTS

ON F ITTIN G

SEAL ING COMP OUND

COUN TERTO P

(BY OTHER S)

1/2

(13m m)

36" ( 914mm )

SUGG ESTED

FINI SHED FLOOR

5-3/ 4"

(146 mm)

5-3/ 4"

(146 mm)

165m m (6-1 /2)

3/8" O.D. BEND ABLE TUBI NG

2-1/ 8" (54m m)

2" (5 1mm)

OPTI ONAL

FINI SHED WALL OR S PLASH BACK

4"(102 mm)

1-1/ 2" (38 mm) DIA. HOLE S TYP.

C/L

22"

(559 mm)

7183 .804 4 HO LE

7183 .805

5 HO LE

4" (102 mm)

3-1/ 2

(89m m)

DIA.

7-3/ 8"

(187 mm)

8-5/ 8"

(219 mm)

14-5 /8"

(372 mm)

12-1 /4"

(311 mm)

20-3 /4"

(527 mm)

41-1 /2"

(105 4mm)

*CU TOUT NOTE

1-1/ 2" (38 mm)

RAD. TYP.

9-1/ 8

(232 mm)

5-3/ 4

(146 mm)

(178 mm)

1-1/ 2" O.D . TAIL PIECE

SEAL ING COMP OUND

COUN TERTOP

(BY OTHERS )

36" (91 4mm)

SUGG ESTED

FINI SHED F LOOR

5-3/ 4

(146 mm)

5-3/ 4

(146 mm)

6-1/ 2

(165 mm)

2-1/ 8

(54m m)

2" (51 mm)

OPTI ONAL

FINI SHED W ALL OR S PLASHB ACK

4"(102 mm)

1-1/ 2" (38 mm) DIA. HOLES TYP.

C/L

(559 mm)

7183 .804 4 HO LE

7183 .805

5 HO LE

(102 mm)

3-1/ 2

(89m m)

DIA.

7-3/ 8

(187 mm)

8-5/ 8

(219 mm)

14-5 /8

(372 mm)

12-1 /4

(311 mm)

20-3 /4

(527 mm)

41-1 /2

(105 4mm)

CUTO UT

N OTE

1-1/ 2" (38 mm)

RAD. TYP.

MOUN TING C LIP (SEE DETAI L)

DETAI L OF MOUNTI NG CLI P

(KIT No.79 1239-1 00)

BRASS

INSER T

1/2

(13mm )

MIN.

REFER TO IN STRUC TIONS

PROVI DED WI TH KI T FOR

ADDIT IONAL INFOR MATION

CLIP MACH. SCREW

SINK

SILHOUETTE™

TRIPLE BOWL SINK

AMERICAST

NOTES:

COUNTERTOP CUTOUT 1022mm x 527mm WITH 25mm RADIUS

(40-1/4 X 20-3/4 WITH 1" RADIUS) AT CORNERS.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ASME Standard A112.19.4 These measurements are subject to c hange or cancellation. No responsibility is assumed for use of superseded or voided leaet.

NOTES:

TEMPLATE PROVIDED WITH MOUNTING KIT 791239-100 FOR

EXPOSED FAUCET DECK OR UNDERCOUNTER FAUCET DECK COUNTERTOP CUTOUT VARIATIONS.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ASME Standard A112.19.4 These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaet.

Undercounter Mount

G18

Revised 2/08