American Standard 7173.803, 791123-100, 7173.805, 7173.001, 7173.804 User Manual
© 2003 American Standard Inc.
KS-53
Revised 3/03
LAKELAND™ 31”
LARGE SINGLE BO WL SINK
AMERICAST®
LAKELAND 31” LARGE SINGLE BOWL
KITCHEN SINK
• Americast
®
brand engineered material
• Single bowl design
• Self-rimming or undercounter installation
• Silicone sealant supplied
• Available in 1, 3,4 or 5 faucet hole configuration
Self-Rimming:
❏ 7173.001 Center hole only
❏ 7173.803 3 hole
❏ 7173.804 4 hole
❏ 7173.805 5 hole (Illustrated)
Undercounter Installation:
❏ 791123-100 Mounting Kit (consists of
cut-out templates and mounting clips
Nominal Dimensions: 787 x 559 x 241mm
(31" x 22" x 9-1/2")
Bowl sizes:
679mm (26-3/4") wide, 413mm (16-1/4") front to
back 229mm (9") deep
Compliance Certifications Meets or Exceeds the Following Specifications:
• ASME A112.19.4M for Americast Plumbing Fixtures
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
* See faucet section for additional models available
To Be Specified
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Soap Dispenser: 4503.115, Color:
❏ Trap:
Shown with 7230.152H Heritage Kitchen Faucet with
Cross handles (not included)
See reverse side for roughing-in dimensions
© 2003 American Standard Inc.
KS-54
LAKELAND™ 31”
LARGE SINGLE BO WL SINK
AMERICAST®
7173.001/803/4/5Self-Rimming
7173.001/803/4/5 Undercounter Mount
NOTES:
TEMPLATE PROVIDED WITH MOUNTING KIT 791123-100 FOR UNDERCOUNTER, INSTALLATION AND COUNTERTOP CUTOUT.
FITTINGS AND UNDERCOUNTER MOUNTING KIT NOT INCLUDED AND
MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR WALL & COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided leaflet.
●
●
NOTES:
COUNTERTOP CUTOUT 756mm X 527mm WITH 25mm RADIUS (29-3/4
X 20-3/4 WITH 1” RADIUS)
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR WALL & COUNTERTOP
SUPPORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.
FINISHED WALL OR SPLASHBACK
102mm
51mm (2
OPTIONAL
7173.805
(5 HOLES)
54mm
(2-1/8)
206mm
(8-1/8)
559mm
(22)
89mm
(3-1/2)
DIA.
COUNTERTOP
BY OTHERS
COUPLING NUTS
ON FITTING
102mm
(4)
102mm
(4)
HC
38mm
(1-1/2)
RAD TYP.
213mm
(8-3/8)
787mm
(31)
203mm
(8)
*3/8 O.D. BENDABLE TUBING
1-1/2 O.D. TAILPIECE
102mm
(4)
(4)
394mm
(15-1/2)
13mm
E
254mm*
FINISHED FLOOR
38mm
(1-1/2) DIA.
HOLES TYP.
(1/2)
(10)
SPRAY
7173.804
(4 HOLES)
●
CUTOUT NOTE
SEALING
COMPOUND
229mm
(9)
146mm
(5-3/4)
TO FINISHED
FLOOR (OPTIONAL)
914mm
(36)
FAUCET
RELIANT 4205.241
TOP MOUNT
6270.000
E
*
41mm(1-5/8)
51mm (2
OPTIONAL
206mm
559mm
(22)
(3-1/2)
(SEE DETAIL)
●
CUTOUT NOTE
COUNTERTOP
BY OTHERS
COUPLING NUTS
ON FITTING
(8-1/8)
89mm
DIA.
7173.805
(5 HOLES)
MOUNTING CLIP
*3/8 O.D. BENDABLE TUBING
FAUCET
RELIANT 4205.241
TOP MOUNT
FINISHED WALL OR SPLASHBACK
54mm
(2-1/8)
6270.000
102mm
102mm
102mm
(4)
(4)
38mm
(1-1/2)
RAD TYP.
213mm
(8-3/8)
203mm
(4)
HC
787mm
(31)
(8)
1-1/2 O.D. TAILPIECE
E
*
41mm(1-5/8)
38mm
102mm
(1-1/2) DIA.
(4)
HOLES TYP.
394mm
(15-1/2)
13mm
(1/2)
E
254mm*
(10)
FINISHED FLOOR
SPRAY
7173.804
(4 HOLES)
DETAIL OF MOUNTING CLIP
(KIT No.791123-100)
BRASS
INSERT
SINK
REFER TO INSTRUCTIONS
PROVIDED WITH KIT FOR
ADDITIONAL INFORMATION
SEALING
COMPOUND
241mm
(9-1/2)
146mm
(5-3/4)
914mm
(36)
TO FINISHED
FLOOR (OPTIONAL)
MACH.
SCREW
CLIP
13mm
(1/2)
MIN.
Loading...