American Standard 7144.803, 7144.804 User Manual

DOUBLE BOWL KITCHEN SINK

• Acid-resisting enameled steel

• Double bowl design

• Top mount installation

• Available in 3 or 4 faucet hole congurations

• Silicone sealant supplied

Top Mount:

❏ 7144.803 3-Hole ❏ 7144.804 4-Hole

Nominal Dimensions:

838 x 559 x 184mm (33" x 22" x 7-1/4")

Bowl sizes:

359mm (14-1/8") wide 413mm (16-1/4") front to back 178mm (7") deep

DOUBLE BOWL SINK

SINGLE BOWL SINK

ENAMELED STEEL

Enameled Steel Double Bowl Sink

Compliance Certications Meets or Exceeds the Following Specications:

• ASME A112.19.4M for Enameled Steel Plumbing Fixtures

SINGLE BOWL KITCHEN SINK

• Acid-resisting enameled steel

• Single bowl design

• Acid-resisting glossy porcelain nish

• Top mount installation

• Available in 3 or 4 faucet hole congurations

• Silicone sealant supplied

Top Mount:

❏ 7143.803 3-Hole ❏ 7143.804 4-Hole

Nominal Dimensions:

635 x 559 x 184mm (25" x 22" x 7-1/4")

Bowl sizes:

552mm (21-3/4") wide 413mm (16-1/4") front to back 178mm (7") deep

Compliance Certications Meets or Exceeds the Following Specications:

• ASME A112.19.4M for Enameled Steel Plumbing Fixtures

Enameled Steel Single Bowl Sink

SEE REVERSE SIDE FOR ROUGHING-IN DIMENSIONS

To Be Specied:

❏ Color: (specify 208 White Heat or 345 Bisque) ❏ Faucet*: (specify nish) ❏ Basket Strainer: 4331.013 (Chrome only) ❏ Soap Dispenser*: 4503.115 (specify color) ❏ Trap:

Optional Accessories:

❏ Large Wood Cutting Board: 9000.250 ❏ Small Wood Cutting Board: 9000.185 ❏ Colander For Cutting Board: 8102.100, Color: ❏ Large Colander: 8103.100, Color:

* See faucet section for available models

G49

Revised 2/08

7144.803/804/805 Top Mount

12-1 /4"

(311 mm)

33"

(838 mm)

4" (1 02mm)

4" (102 mm)

22"

(559 mm)

CUT OUT

NOTE

2-1/ 4"

(57m m)

7144 .804 4 HO LE

7144 .805 5 HO LE

FINI SHED WALL O R SPL ASH BA CK

38mm (1-1 /2)

DIA. (TYP .)

OPTI ONAL

COUN TER T OP (BY OTHE RS)

C/L

15-5 /8"

(397 mm)

FINI SHED

FLOO R

3-1/ 2" (89m m)

CLAM PING DETAIL

LUG AND SCRE W ASSE MBLY

COUN TERTO P

13/1 6"

(21m m)

MAX.

16-1 /2"

(419 mm)

1-1/ 2" O.D . TAIL PIECE

36" ( 914mm )

SUGG ESTED

(152 mm)

1/2" (13m m)

6-3/ 4"

(171 mm)

1-1/ 2"

(38m m) R.

CLA MPING DETAIL

LUG AND SCR EW ASS EMBLY

COU NTERTO P

12- 1/2"

(31 8mm)

714 3.804 4 H OLE

FIN ISHED WALL O R SPL ASH BA CK

C/L

OPT IONAL

COU NTER T OP (BY OTHE RS)

FIN ISHED

FLO OR

CU TOUT

NOT E

13/ 16"

(21 mm)

MAX .

1-1 /2" O.D .

TAI LPIECE

36" (914mm )

SUG GESTED

(15 2mm)

1/2 " (13 mm)

6-3 /4"

(17 1mm)

12- 1/4"

(31 1mm)

22"

(55 9mm)

2-1 /4"

(57 mm)

3-1 /2" (89 mm)

1-1 /2"

(38 mm) R.

4" ( 102mm)

38m m (1-1 /2)

DIA . (TYP .)

25"

(63 5mm)

DOUBLE BOWL SINK

SINGLE BOWL SINK

ENAMELED STEEL

NOTES:

COUNTERTOP CUTOUT 80 0 x 521mm WITH 19mm RADIUS

(31-1/2" x 20-1/2" WITH 3/4’ RADIUS) AT CORNERS.

STRAINERS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ASME Standard A112.19.4 These measurements are subject to c hange or cancellation. No responsibility is assumed for use of superseded or voided leaet.

NOTES:

COUNTERTOP CUTOUT 597 x 521mm WITH 19mm RADIUS

(23-1/2" x 20-1/2" WITH 3/4’ RADIUS) AT CORNERS.

●

Wood - 19mm (3/4")

Marble and Solid Surface - 12mm (1/2")

STRAINERS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND COUNTERTOP SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ASME Standard A112.19.4 These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaet.

Recommended minimum counter top thickness:

7143.803/804 Undercounter Mount

G50

Revised 2/08