American Standard 7144.805, 7143.804, 7143.803 User Manual
© 2003 American Standard Inc.
KS-55
DOUBLE BO WL™ SINK
SINGLE BO WL™ SINK
ENAMELED STEEL
DOUBLE BOWL KITCHEN SINK (shown)
❏ 7144.803 3-Hole
❏ 7144.804 4-Hole
❏ 7144.805 5-Hole
Product Features:
• Acid-resisting enameled steel
• Double bowl design
• Self-rimming installation
• Available in 3, 4 or 5 faucet hole configurations
• Silicone sealant supplied
Nominal Dimensions: 838 x 559 x 184mm
(33" x 22" x 7-1/4")
Bowl sizes:
359mm (14-1/8") wide, 413mm (16-1/4") front
to back, 178mm (7") deep
Compliance Certifications Meets or Exceeds the Following Specifications:
• ASME A112.19.4M for Enameled Steel Plumbing
Fixtures
To Be Specified
❏ Color: (specify White Heat,Bone, or Bisque)
❏ Faucet*: (specify finish)
❏ Basket Strainer: 4331.013 (Chrome only)
❏ Soap Dispenser*: 4503.115 (specify color)
❏ Trap:
* See faucet section for additional models available
Revised 8/02
SINGLE BOWL KITCHEN SINK
❏ 7143.803 3-Hole
❏ 7143.804 4-Hole
Product Features:
• Acid-resisting enameled steel
• Single bowl design
• Self-rimming installation
• Available in 3 or 4 faucet hole configurations
• Silicone sealant supplied
Nominal Dimensions: 635 x 559 x 184mm
(25" x 22" x 7-1/4")
Bowl sizes:
552mm (21-3/4") wide, 413mm (16-1/4") front to
back, 178mm (7") deep
Compliance Certifications Meets or Exceeds the Following Specifications:
• ASME A112.19.4M for Enameled Steel Plumbing
Fixtures
ROUGHING-IN DIMENSIONS SHOWN ON REVERSE SIDE OF PAGE
© 2003 American Standard Inc.
KS-56
DOUBLE BO WL™ SINK
SINGLE BO WL™ SINK
ENAMELED STEEL
NOTES:
COUNTERTOP CUTOUT 800 x 521mm WITH 19mm RADIUS (31-1/2” x 20-1/2” WITH 3/4’
RADIUS) AT CORNERS.
PROVIDE SUITABLE REINFORCEMENT FOR WALL AND COUNTERTOP SUPPORTS.
STRAINERS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
Important: Dimensions of fixtures are nominal and may vary within the range of tolerances
established by ANSI Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility is assumed for
use of superseded or voided pages.
NOTES:
COUNTERTOP CUTOUT 597 x 521mm WITH 19mm RADIUS (23-1/2” x 20-1/2” WITH 3/4’
RADIUS) AT CORNERS.
PROVIDE SUITABLE REINFORCEMENT FOR WALL AND COUNTERTOP SUPPORTS.
STRAINERS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
Important: Dimensions of fixtures are nominal and may vary within the range of tolerances
established by ANSI Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility is assumed for use
of superseded or voided pages.
7144.803/804/805
7143.803/804
38mm (1-1/2)
DIA. (TYP.)
102mm
(4)
102mm
(4)
102mm
(4)
102mm
(4)
7144.805
5 HOLE
OPTIONAL
311mm
(12-1/4)
38mm R.
(1-1/2)
13mm
(1/2)
171mm
(6-3/4)
152mm
(6)
COUNTERTOP
21mm
(13/16)
MAX.
LUG AND
SCREW
ASSEMBLY
89mm
(3-1/2)
397mm
(15-5/8)
838mm
(33)
1-1/2 O.D. TAILPIECE
C/L
7144.804
4 HOLE
419mm
(16-1/2)
COUNTER TOP (BY OTHERS)
FINISHED
FLOOR
57mm
(2-1/4)
559mm
(22)
CUTOUT
*
NOTE
914mm
(36)
SUGGESTED
FINISHED WALL OR SPLASH BACK
38mm (1-1/2)
OPTIONAL
311mm
(12-1/4)
38mm R.
(1-1/2)
DIA. (TYP.)
102mm
(4)
C/L
318mm
(12-1/2)
635mm
(25)
102mm
(4)
89mm
(3-1/2)
102mm
(4)
7143.804
4 HOLE
57mm
(2-1/4)
559mm
CUTOUT
*
NOTE
(22)
FINISHED WALL OR SPLASH BACK
13mm
(1/2)
171mm
(6-3/4)
COUNTERTOP
21mm
(13/16)
MAX.
CLAMPING DETAIL
152mm
LUG AND
SCREW
ASSEMBLY
(6)
COUNTER TOP (BY OTHERS)
FINISHED
FLOOR
1-1/2 O.D.
TAILPIECE
914mm
(36)
SUGGESTED
Loading...