American Standard 7105.801, 7105.821 Installation Manual
INSTALLATION
INSTRUCTIONS
STUDIO® S
DUAL CONTROL WIDESPREAD
7105.801
7105.821
LAVATORY FAUCET
WITH SPEED CONNECT® DRAIN
Congratulations on purchasing your American Standard faucet
with Speed Connect drain, a feature found only on American
Standard faucets.
Speed Connect® Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the rst time, every time.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
RECOMMENDED TOOLS
Flat Head Screwdriver
1
INSTALL SPOUT
Fig. A.
• Insert SHANK (1) CABLE CONNECTOR (2) and HOSE (3) through center hole,
making sure SEAL WASHER (4) is properly seated in spout base.
• From below, push GASKET (6) with RETAINING WASHER (7) onto MOUNTING
STUD (5). Secure faucet with MOUNTING NUT (8), pushing faucet to back of
sink, so SUPPLIES (3) rests against mounting hole.
• Align and center SPOUT (1). Tighten LOCKNUT (6).
1A
INSTALL VALVE BODIES
Fig. B.
• Place SEAL WASHER (8) under HANDLE (9) and
make sure it sits properly inside the groove of the
deck adapter.
• Remove LOCKNUT (10) and RUBBER WASHER
(11), FRICTION WASHER (11a) from SIDE VALVE
SHANKS (12).
• Insert Hot and Cold SIDE VALVE HOSES (13),
FLEXIBLE SUPPLIES (13a) into mounting holes
making sure the SEAL WASHERS (8) are
properly seated in each HANDLE BASE (9).
• Assemble SPACER (14) RUBBER WASHER (11),
FRICTION WASHER (11a) and thread LOCKNUT
(10) onto each SIDE VALVE SHANK (12) from
underside of sink or mounting surface.
NOTE: SPACER (14) not needed for deck
thickness larger then 3-1/4".
• Align and center SIDE VALVES. Tighten
LOCKNUTS (10).
CAUTION
Turn off hot and cold water
supplies before begining.
Adjustable Wrench Tubing CutterSlip Jaw Pliers
12
14
11
11a
10
13 Red Stripe
Fig. B.
9
8
13a
13a
(HOT)
Certied to comply with ANSI A112.18.1M
Hex Wrench
Fig. A.
SPOUT BASE
5
1
13 Blue Stripe (COLD)
4
3
6
7
8
2
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2016
- 1 -
M965780 (6/17)
2
POP-UP DRAIN
Fig. A. Fig. B.
• Remove CLEAR PLASTIC COVER (1).
• Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).
• Tighten TAIL PIECE (4) on DRAIN BODY before
installing DRAIN BODY. Fig. B.
3
REMOVE FLANGE
• Thread FLANGE (1) counter-clockwise and
remove FLANGE (1) and FOAM GASKET (2)
from drain body. Fig. A.
• Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3). Fig. B.
2
Fig. A.
1
1
3
DRAIN
BODY
4
Fig. B.
2
4
3
4
INSTALL DRAIN FROM
BELOW FIXTURE
• From under side of SINK
install DRAIN BODY (1) up
through drain outlet.
Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the SINK.
• Install FOAM GASKET (3) on
to bottom of ange and
assemble FLANGE (4) onto
drain body from above sink
and tighten FLANGE (4) rmly.
6
FLANGE GASKET AND POP-UP KNOB
• Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.
• P O P -UP KNOB (1) must be pressed completely
down Fig.B while pop up is in the full up
position.
4
3
5
REAR OF SINK
DRAIN
OUTLET
TIGHTEN LOCKNUT
• Tighten LOCKNUT (1) rmly with Adjustable
Wrench or Channel Locks.
1
2
Fig. A. Fig. B.
1
WHITE FOAM
GASKET
NOT VISIBLE
DRAIN
FLANGE
1
DOWN
2
- 2 -
M965780 (6/17)
7
ATTACH CABLE CONNECTOR
• Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tail piece on pop-up drain is
1-1/4" O.D. Fig. B.
Fig. A.
Fig. B.
1
8
CHECK OPERATION OF POP-UP
• Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes.
Note: If STOPPER (2) does not open and close properly then
refer to the “troubleshooting section” of these instructions.
9
MAKE WATER SUPPLY AND WASTE CONNECTIONS
• Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on tting supplies are 3/8" compression.
Connect FLEXIBLE SUPPLY (1) (Marked with a Red Band) to the
Left wall supply and FLEXIBLE SUPPLY (2) (Marked with a Blue
Band) to Right wall supply.
• Connect the VALVE HOSES (3, 3a) to SPOUT TEE (4).
Use adjustable wrench to tighten connections.
Do not over tighten.
• Faucet supplies are 20" long from faucet base.
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are to long, loop as
illustrated to avoid kinking.
• Connect 1-1/4" O.D. tail piece on POP-UP DRAIN to
waste outlet.
2
1-1/4" O.D.
1
2
3a
3
Red Stripe (HOT)
1
- 3 -
WASTE
OUTLET
HOT
COLD
2
Blue Stripe
(C0LD)
M965780 (6/17)
4
Loading...