American Standard 7100.2XX User Manual

Installation

Instructions

7100.2XX

SINGLE-HOLE BAR/PANTRY FAUCET WITH SWING SPOUT

Thank you for selecting American-Standard... the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

MODEL 7190.132 MODEL 7100.2XX

7190.132

Certiﬁed to comply with ANSI A112.18.1M

U.S. Patent No. 5,819,789

34440 REV. 1.4

066108-YYY0A

AERATOR

012087-0070A

SPOUT SEAL KIT

A911758-0070A

RUBBER RING

M961714-0070A

MOUNTING KIT

012088-YYY0A

SWING SPOUT KIT

028611-0070A

HANDLE SCREW

A908424-YYY0A

HANDLE

028610-0070A

CARTRIDGE

066108-YYY0A

AERATOR

012087-0070A

SPOUT SEAL KIT

012671-0070

RUBBER RING

012094-0070A

MOUNTING KIT

012088-YYY0A

SWING SPOUT KIT

030741-0070A

CARTRIDGE SEAL KIT

028611-0070A

HANDLE SCREW

028610-0070A

CARTRIDGE

Replace the "YYY" with appropriate ﬁnish code

CHROME POL. BRASS SATIN NICKEL SATIN/BRASS CHROME/POL. BRASS

002 099 295 297 299

024220-0070A

SUPPLY NUT

For toll-free information and answers to your questions, call:

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Product names listed herein are trademarks of American Standard Inc. © AS America, Inc. 2008

HOT LINE FOR HELP

1-800-442-1902

Weekdays 8:00 a.m. to 6:00 p.m. EST

Weekdays 8:00 a.m. to 7:00 p.m. EST

IN MEXICO 01-800-839-1200

Replace the "YYY" with appropriate ﬁnish code

CHROME WHITE BONE POL. BRASS

002 020 021 099

SWING SPOUT ASSEMBLY

CAUTION

Turn off hot and cold water supplies before beginning.

Assemble the SPOUT (3) and tighten the SPOUT NUT

FITTING INSTALLATION

Remove LOCKNUT (1), BRASS WASHER (2), and GASKET

Place RUBBER RING (4) in recess of ﬁtting.

Insert inlet hoses (on model 7190.132 only) and THREADED SHANK through hole of sink making certain RUBBER RING recess of the ﬁtting base.

Assemble GASKET (3), BRASS WASHER (2), and LOCKNUT underside of sink deck.

Tighten the LOCKNUT (1) securely.

For Model 7190.132 Only

Connect the hot water supply to the left inlet hose and the cold water supply to the right inlet hose using appropriate connectors.

For Model 7100.2XX Only

Connect hot or cold water supply lines to shank using sealant, appropriate connectors, and coupling nuts.

(4) until snug on VALVE BODY.

(3) from ﬁtting.

(4) is properly seated in the

(1) onto the THREADED SHANK from

MODEL

7190.132

RECESS

FLEXIBLE

INLET HOSES

HOT

COLD

MODEL

7100. 2XX

RECESS

SHANK

2 1

SUPPLY

NUT

TEST INSTALLED FAUCET

Remove AERATOR. With handle in OFF position, turn on water supplies

and check all connections for leaks.

SERVICE

To change direction of handle rotation, proceed as follows:

Turn valve to OFF position. Remove INSERT and HANDLE SCREW. Slip HANDLE with ADAPTER off. Remove SPRING CLIP (1). Lift STOP WASHER (2), turn 90° and replace. Replace SPRING CLIP (1). Replace ADAPTER, HANDLE, SCREW, and INSERT.

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.

90°

Operate both handles to ﬂush water lines thoroughly. Checkspout mounting and hose connections for leaks.

Turn handles into OFF position and replace AERATOR.

AERATOR may accumulate dirt causing distorted and reduced water ﬂow. Remove AERATOR and rinse clean.

If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°.

Plastic SCREEN (3) in CARTRIDGE (4) may accumulate dirt causing reduced water ﬂow. To clean, ﬁrst turn off hot and cold water supplies, then:

Remove INSERT and HANDLE SCREW. Slip HANDLE with ADAPTER off.

Unscrew CARTRIDGE (4) with wrench. Thoroughly rinse plastic SCREEN (3) at base of CARTRIDGE (4). Replace CARTRIDGE (4) until ﬂange is

tight against valve body. Turn valves OFF. Replace ADAPTER, HANDLE, SCREW, and INSERT.

34440 REV. 1.4