American Standard 7075.100, 7075.102, 7075.104 Installation Manual
INSTALLATION
INSTRUCTIONS
COLONY® PRO
SINGLE LEVER MONOBLOCK
LAVATORY FAUCET
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
Screwdriver Adjustable Wrench Tubing CutterChannel Locks
1
INSTALL FAUCET
• Seat SEAL (2) into under side of FAUCET BODY (1).
• Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and DRAIN ASSEMBLY
(8) through the mounting hole of lavatory. Figure A.
• From below, push GASKET (7) and RETAINING WASHER (5) onto
MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (6), pulling
faucet to front of sink, so SUPPLIES (3) rests against mounting hole.
Before nal tightening, make sure collar on MOUNTING NUT (6) is
seated into RETAINING WASHER (5).
• Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6)
to complete faucet mounting.
CAUTION
Turn off hot and cold water
supplies before begining.
7075.100
7075.102
7075.104
Figure A
Certied to comply with ANSI A112.18.1M
(OPTIONAL
DECK PLATE)
2000102P-YYY
COLLAR ON
MOUNTING NUT
6
4
Figure B
1
4
MOUNTING
SURFACE
2
3
5
7
8
5
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2016
- 1 -
M965764 (8/16)
2
INSTALL POP-UP DRAIN
2a
• Push TAIL PIECE (11) down into TRAP (C) (threaded end up).
• Thread LOCKNUT (5), WASHER (4) and GASKET (3)
(Bevel side up) onto DRAIN BODY (10).
• Apply a bead of PUTTY (D) to underside of FLANGE (2).
• Feed DRAIN BODY (10) up through SINK (A) and thread
the FLANGE (2) fully onto DRAIN BODY (10).
• Tighten LOCKNUT (5) rmly, keeping the pivot rod hole pointed
towards the back of the sink.
• Assemble PIVOT ROD (9) as shown in Figure-2a.
Notice the position of the CONCAVE WASHER (G).
• Insert PIVOT ROD (9) into DRAIN BODY (10) and tighten
PIVOT NUT (F).
• Pull TAIL PIECE (11) up and thread tightly into
DRAIN BODY (10).
• Position EXTENSION ROD (7) onto POP-UP ROD (E) and tighten
THUMBSCREW (6).
• Remove one end of CLIP (8) from PIVOT ROD (9) by squeezing ENDS TOGETHER WHILE SLIDING.
• Insert PIVOT ROD (9) into second or third hole in EXTENSION ROD (7) and reassemble CLIP (8).
• DROP STOPPER (1) into DRAIN BODY (10).
• Adjust stopper height by repositioning EXTENSION ROD (7) and tightening THUMBSCREW (6).
3
CHECK OPERATION OF POP-UP
A
4
10
11
1
2
3
5
C
1-1/4"
D
E
G
F
6
7
8
F
9
• Operate LIFT KNOB (1) to verify that
STOPPER (2) opens and closes.
4
MAKE WATER SUPPLY AND WASTE CONNECTIONS
• Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on tting supplies are 3/8" compression.
Connect left SUPPLY (1) to Hot (Marked with a Red Band)
and right supply to COLD (2) wall supply.
• Faucet supplies are 20" long from faucet base.
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are to long, loop as
illustrated to avoid kinking.
1
2
APPROX. 20"
2
1
RED
BAND
BLUE
BAND
3/8" COMPRESSION
- 2 -
HOT
COLD
M965764 (8/16)
Loading...