American Standard 7048.303, 7048.301, 7048.304 User Manual
(w/Recess for Tile) DOUBLE BOWL SINK
7-1/ 8"
(181 mm)
TILE RECESS AREA
6-3/16" x 24-1/2" x 3/8"
(157 x 822 x 10mm DEEP)
(2) 1-1/2 " O.D.
TAIL PIECE
257m m
(10- 1/8")
146m m
(5-3 /4")
248m m
(9-3 /4")
Y
COUN TERTO P
(BY OTHER S)
CABI NET
FASC IA
5-3/ 4"
(146 mm)
36" ( 914mm )
SUGG ESTED
FINI SHED
FLOO R
8-1/ 8"
(206 mm)
3/8"
(10m m)
4"
(102 mm)
HOT
COLD
FINI SHED WALL O R
SPLA SH BA CK
4"
(102 mm)
3-1/ 2"
(89m m) DI A.
2-3/ 4"
(108 mm)
4"
(102 mm)
11"
(279 mm)
18"
(457 mm)
1-3/ 8" (35 mm) D IA.
HOLE S TYP.
7048 .301
1 HO LE
VARI ATION
8-3/ 4"
(222 mm)
C/L
SPRA Y
7048 .304
4 HO LE
VARI ATION
7048 .303
3 HO LE
VARI ATION
1-3/ 4"
(44m m) DI A.
2"
(51m m) OP TIONAL
22"
(559 mm)
CUTO UT
NOTE
*
1-1/ 2" REF .
(38m m)
SEAL ING
COMP OUND
36"
(914 mm)
4-1/ 2"
(114 mm)
2" (5 1mm)
FRON T OF
APRO N
9-1/ 2"
(241 mm)
1" (2 5mm)
RAD. TYP.
CHANDLER™ FRONT APRON (w/Recess for Tile)
DOUBLE BOWL KITCHEN SINK
• Dupont Corian® surface
• Double bowl design
• Front apron panel - recessed for tile
• Top mount
• Shown with 4771.702 Hampton faucet with
porcelain cross handles (not included)
• Silicone sealant supplied
• Available in center hole only, 3, or 4 faucet
hole conguration
❏ 7048.301 Center hole only
❏ 7048.303 3 hole
❏ 7048.304 4 hole
Nominal Dimensions:
914 x 559 x 254mm
(36" x 22" x 10-1/2")
CHANDLER™ FRONT APRON
DUPONT CORIAN
®
Bowl sizes:
Right Hand: 359mm (14-1/8") wide
16-1/4" (413mm) front to back
203mm (8") deep
Left Hand: 432mm (17") wide
476mm (18-3/4") front to back
254mm (10") deep
Compliance Certications Meets or Exceeds the Following Specications:
• ANSI Z124.6 for Non-Metallic Sinks
To Be Specied:
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Basket Strainer: 4331.013
❏ Soap Dispenser: 4503.115, Color:
❏ Traps:
* See faucet section for available models
© 2008 AS America Inc.
NOTES:
FOR COUNTERTOP CUTOUT SEE INSTALLATION INSTRUCTIONS
*
SUPPLIED WITH SINK.
TILE RECESS ARE A DESIGNED FOR FOUR (4) 6" x 6" x 5/16" THICK
CERAMIC TILES. TILES NOT INCLUDED. BE SURE TO USE TILES
THAT FIT RECESS.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL AND
COUNTERTOP SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ANSI Standard Z124.6
These measurements are subject to c hange or cancellation. No responsibility
is assumed for use of superseded or voided leaet.
G13
Revised 6/06
© 2008 AS America Inc.
G14
Loading...