American Standard 7048 User Manual
™
M A D E W I T H
Installation
Instructions
CHANDLER™ KITCHEN SINK
MODEL 7048
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI Z124.6
U.S. Patent No. D-355,023
Observe local plumbing and building codes.
790753-100 REV A
BEFORE YOU BEGIN...Unpack new sink and
inspect carefully for damage. Replace the sink
in its original packing carton to protect it until
you are ready to begin installation.
Recommended Tools & Materials
Putty Knife
Pipe Wrench
Channel Locks
Phillips Screwdriver
Regular Screwdriver
Adjustable Wrench
Drill
Basin Wrench
Saber Saw
Plumbers' Putty or
Caulking
Tubing Cutter
Tape Measure
Hacksaw
AFTER THE CUTOUT IS DRAWN...
1
Drill a clearance hole
inside the cutout line
as marked on the
countertop.
Perimeter
of sink
Cutout
CUTOUT DIMENSIONS FOR SINK
Locate and mark center lines of sink on countertop.
Provide proper clearance under the countertop for
the faucet supply lines and the structural parts of the
cabinet.
By using the diagram below and measuring your sink,
draw the outline of the sink onto the countertop. This
is not the cutting outline.
CUTOUT FOR NEW INSTALLATION
36" (914mm)
32" (813mm)
10-1/2"
(267mm)
22"
(559mm)
21"
(533mm)
CUTTING
LINE
SINK
OUTLINE
1/2" (13mm)TYP.
2
Cut opening on cut
line inside the peri-
Perimeter
of sink
MODIFICATION REQUIRED TO FIT CHANDLER SINK
INTO A STANDARD 33" X 22" SINK CUTOUT
meter of sink.
Cutout
10-1/2"
(267mm)
3
Mount the faucet and
drain assembly on the
sink following the
manufacturer's
instructions.
Product names listed herein are trademarks of American Standard Inc. unless otherwise noted.
Corian® Dupont registered trademark
32"(813mm)
19-1/2"(495mm)
CENTER LINE
21" Radius
(533mm)
CUTTING
LINE
35"
(889mm)
19-1/2"(495mm)
SINK
OUTLINE
1-1/2"
(38mm)
21" Radius
(533mm)
21"
(533mm)
1/2" (13mm)TYP.
© American Standard Inc. 2004
4
Before applying the
sealant, place the sink
temporarily into the
cutout. Check for
alignment and clearance, then trace
around the outside
edge of the sink as
a guide for installation location and application of
sealant. Remove sink.
5
Apply a masking tape
outline 1/8" outside
traced outline as a
guide for application
of silicone
sealant.
Masking
tape
outline
Cutout
1/8"
Sink
outline
Apply a generous portion of silicone sealant inside line
6
traced on countertop. Carefully lower sink into place
and press down firmly. Use guidelines for proper
positioning. Using water to dampen your finger,
remove excess sealant for a smooth even line. Apply
additional sealant if necessary to provide a uniform
bead from the rim of sink to the masking tape line as
shown. Carefully remove tape. Dampen finger and run
it slightly over the sealant to remove any high spots.
Sink
Masking
Tape
Silicone
Sealant
7
Connect supply lines to
faucet finger tight, and
carefully bend to engage
with the supply stops.
Tighten connections to
faucet for secure seal.
AMERICAN STANDARD TEN-YEAR LIMITED WARRANTY
®
CORIAN
If inspection of the Corian Sink of this American Standard product, within ten years after
its initial purchase, confirms that it is defective in materials or workmanship, American
Standard will repair or, at its option, exchange the product for a similar model.
This warranty applies only to the original purchaser and installation of these products. All
labor and transportation costs or charges incidental to warranty service are to be borne by
the original consumer-purchaser.
This limited warranty does not apply to local building code compliance. Since local
building codes vary considerably, the purchaser of this product should check with a local
building or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been fabricated or modified in a manner
inconsistent with the product as shipped by American-Standard; moved from its initial place
of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or
other damages; or if it was not installed in accordance with American Standard's
instructions.
American Standard's option to repair or exchange the product under this warranty does
not cover any labor or other costs of removal or installation, nor shall American Standard
be responsible for any other incidental or consequential damages attributable to a
product defect or to the repair or exchange of a defective product, all of which are
expressly excluded from this warranty. (Some states or provinces do not allow the
exclusion or limitation of implied warranties, so this exclusion may not apply to you.)
This warranty gives you specific legal rights. You may have other statutory rights that
vary from state to state of from province to province, in which case this warranty does not
affect such statutory rights.
In the United States:
American Standard Inc.,
P. O. Box 6820
Piscataway, NJ 08855
Attention: Director of Consumer Affairs
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
SINK
For residents of the United States,
warranty information may also be
obtained by calling the following
toll free number: (800) 442-1902
In Canada:
American-Standard,
2480 Stanfield Road,
Mississauga, Ontario
Canada L4Y 1S2
Toll free: (800) 387-0369
8
Connect drain assembly
hand tight to check
alignment. It may be
necessary to cut off part
of the tailpiece (area "A")
or part of the horizontal
leg of the trap (area "B").
Secure joint for watertight assembly.
Corian® Care &
Maintenance Tips
Cleaning
Most dirt
and stains
Water
marks
Difficult
stains
Disinfecting
Maintenance
A
Double Bowl
Use soapy water or
ammonia-based cleaner.
Wipe with damp cloth; towel dry.
Use an abrasive cleanser and
a green Scotch-Brite* pad.
Occasionally wipe surface with
diluted household bleach
(1 part water/1 part bleach).
Rub with Scotch-Brite* pad alone.
B
Trap
790753-100 REV A
*Registered trademark of the 3M Company
2
Loading...