American Standard 6801, 6830, 6802, Heritage 6831, 6832 User Manual

Installation Instructions

6801 SERIES 6802 SERIES

HERITAGE SERIES SPREAD LAVATORY

FAUCETS

6830 SERIES 6831 SERIES 6832 SERIES

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

6802 SERIES

CONVENTIONAL

SPOUT LESS POP-UP

6831 SERIES

GOOSENECK SPOUT

WITH POP-UP

HANDLE

SCREW

CARTRIDGE

ESCUTCHEON

6801

SERIES

HERITAGE

SPOUT

W/POP-UP

RUBBER

GASKET

LIFT

ROD

O-RING

Certified to comply with ANSI A112.18.1M U.S. Patent No. 5,819,789

M34375C

WRENCH

AERATOR

RUBBER

RING

RUBBER

WASHER

BRASS

WASHER

LOCKNUT

COUPLING

NUT

RUBBER

WASHER

RETAINER

LOCKNUT

SEAL

FRICTION

RING

COMPRESSION

NUT

EXTENSION

SCREW

O-RING

TUBE & TEE

ASSEMBLY

THUMBSCREW

CLIP

ACTUATOR

ROD

VALVE

ASSEMBLY

DRAIN

STOPPER

DRAIN

PLUG

GASKET

WASHER

LOCKNUT

GASKET

COUPLING

TAILPIECE

Printed in Mexico

SPOUT OR BASE ASSEMBLY

Insert BASE or SPOUT shank through center hole of SINK, making sure RUBBER GASKET is properly positioned.

Assemble RUBBER WASHER, RETAINER, and LOCKNUT onto threads of SPOUT from underside of SINK.

Insert LIFT ROD through SPOUT (or BASE) and slot of RETAINER.

Align SPOUT and tighten LOCKNUT. Be sure slot in BRASS WASHER is positioned to the rear as shown.

VALVE INSTALLATION (continued)

Prepare TUBE and TEE ASSEMBLY to fit available VALVE location. If necessary, cut and/or bend TUBING carefully. Make sure tube bend is close to the TEE so that it will not effect the compression joint at the VALVE.

Remove COUPLING NUT, FRICTION RING, and RUBBER FERRULE from each valve and slide onto tubing.

Push TUBING ends into VALVE side outlets. Insert VALVES into mounting holes from underside of SINK.

Press TEE onto SHANK of SPOUT making certain that the SHANK O-RING is properly seated on SHANK.

CAUTION

Turn off hot and cold water

supplies before beginning.

RUBBER

GASKET

SINK

SPOUT

RUBBER

WASHER

RETAINER

LOCKNUT

SHANK

O-RING TEE

O-RING

SCREW

VALVE INSTALLATION

Place RUBBER RING into ESCUTCHEON and screw ESCUTCHEON onto VALVE BODY until snug against internal stop.

Tighten LOCKNUT to secure VALVE position. Attach COUPLING to TEE and tighten.

Slide RUBBER FERRULE, FRICTION RING, and COUPLING NUT to outlet of VALVE and tighten COUPLING NUT firmly. Repeat on other VALVE.

Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of right VALVE using appropriate connector.

DRAIN ASSEMBLY

(Models 6802 and 6832 only)

Apply a bead of PUTTY around underside of DRAIN PLUG flange. Insert DRAIN PLUG into SINK drain hole.

Hold DRAIN PLUG to prevent turning and assemble GASKET, WASHER, and LOCKNUT, from underneath sink.

Insert threaded end of TAILPIECE into lower end of DRAIN PLUG. Connect other end to trap.

5/16'' MIN.

PUTTY

RUBBER

GASKET

LOCKNUT

TAIL

PIECE

ESCUTCHEON

FLANGE

RUBBER RING

LEDGE

RUBBER WASHER

BRASS WASHER

LOCKNUT VALVE

BODY

SINK

DRAIN

PLUG

WASHER

DRAIN INSTALLATION

(Models 6801 and 6831 only)

Apply a bead of PUTTY around the underside of DRAIN PLUG flange and insert DRAIN PLUG into SINK drain hole.

Hold DRAIN PLUG firmly to prevent turning, and assemble the GASKET, WASHER, and LOCKNUT from underneath the SINK.

Insert GASKET into COUPLING and attach COUPLING to DRAIN PLUG. Align COUPLING so that the ACTUATOR ROD faces rear of SINK and tighten LOCKNUT to secure position.

TEST INSTALLED FAUCET

Remove AERATOR. With handle in OFF position, turn on water supplies and check

all connections for leaks.

SERVICE

To change direction of handle rotation, proceed as follows:

Turn valve to OFF position. Remove INSERT and HANDLE SCREW. Slip HANDLE with ADAPTER off. Remove SPRING CLIP. Lift STOP WASHER, turn 90 Replace SPRING CLIP. Replace ADAPTER, HANDLE, SCREW, and INSERT.

AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean.

For toll-free information and answers to your questions, call:

Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time Saturdays 8:00 a.m. to 4:00 p.m. Eastern Time

THUMBSCREW

EXTENSION

CLIP

° and replace.

HOTLINE FOR HELP

1 (800) 223-0068

ACTUATOR

ROD

SPRING

CLIP

LIFT ROD EXTENSION

CLIP

ACTUATOR

STOP

WASHER

ROD

Unscrew ACTUATOR NUT and withdraw the ACTUATOR ROD. Drop STOPPER into DRAIN PLUG with the OFFSET SQUARE SLOT

in line with ACTUATOR ROD opening.

Reassemble ACTUATOR ROD. Make sure ROD is inside offset square slot of the stopper. Tighten ACTUATOR NUT.

Insert threaded end of TAILPIECE into lower end of COUPLING. Connect other end of TAIL PIECE to the TRAP.

Slide EXTENSION onto ACTUATOR ROD and secure with CLIP. Slide EXTENSION onto LIFT ROD and tighten THUMBSCREW. Adjust LIFT ROD stroke for proper opening and closing of the

stopper.

Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks.

Operate LIFT ROD and check DRAIN for leaks. Turn handles into OFF position and replace AERATOR.

If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°.

Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow. To clean, first turn off hot and cold water supplies, then:

Remove INSERT and HANDLE SCREW. Slip HANDLE with ADAPTER off. Unscrew CARTRIDGE with wrench. Thoroughly rinse plastic SCREEN at base of CARTRIDGE. Replace CARTRIDGE until flange is tight against valve body. Turn valves OFF. Replace ADAPTER, HANDLE, SCREW, and INSERT.

Product names listed herein are trademarks of American Standard Inc.

American Standard Inc. 1999

CARTRIDGE

SCREEN

M34375C