American Standard 6771 User Manual

Installation
THE
“”
COLLECTION
by
Instructions
6771
MIRROR/MEDICINE CABINET
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
Recommended Tools
10'
Tape Measure
Drill
Regular Screwdriver
LevelTape
 
REQUIRED WALL OPENING
Caution; Before cutting into any existing wall check that there is no interference with piping or electrical wiring.
Determine the height and location and draw center lines to layout the wall opening.
Before installing the medicine cabinet with mirror the dry wall and any finished wall should be completed.

29"
16"
2x4 WALL STUDS 16" ON CENTER
2x4 SIDE
2"
14-3/8"
22"
A
REINFORCEMENT
2x4 TOP SUPPORT
A
2x4 BOTTOM SUPPORT
2x4 WALL STUD
16" ON CENTER
2x4 SIDE
REINFORCEMENT
1/2" DRY WALL
FINISHED WALL
16"
14-3/8"
ROUGH OPENING
INTERIOR DEPTH 4-1/8" MINIMUM
"A - A"
OUTSIDE DIMENSIONS OF CABINET
ARE 14" X 21-3/4"
SUGGESTED FRAMING FOR ROUGH OPENING
DRY WALL AND FINISHED WALL
4" CABINET DEPTH
INSTALL MIRROR/MEDICINE CABINET
!
Note: Cabinet can be installed either right hand or left hand by rotating cabinet180 degrees.
Install MIRROR/MEDICINE CABINET into finished opening in wall. Check for level and that cabinet frame fits flush against finished wall. Shim as required to make level. (Figure A)
Drill two 1/8" dia. pilot holes into top and bottom of cabinet. Secure cabinet to framing with wood screws. (Figure B)
PILOT HOLES
Figure A Figure B
INSTALL MOUNTING PLATES
Note: Refer to Figure A for use of
To use TEMPLATES (A & B),
Starting at lower left corner of cabinet frame, locate the template as illustrated. Tape into place and mark the three centers of the MOUNTING PLATE (1). Use TEMPLATE (A) for corners 1 & 3 and TEMPLATE (B) for corners 2 & 4 marking the MOUNTING PLATE (1) locations and mounting holes. Check with a level that the center to center measurements are level.
To use DIMENSIONS,
indicated to locate the center of each MOUNTING PLATE (1). Mark the centers for the left side MOUNTING PLATE (1) and use the same measurements to locate the centers of the right side. Check with a level that the center to center measurements are level.
For best installation results it is recommended to secure MOUNTING PLATES (1) to reinforcements studs. No Anchors are needed. Drill small pilot holes for SCREWS (3).
For installations on drywall without reinforcement studs,
MOUNTING PLATE (1) to wall. Place #2 Phillips screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with the wall. Place MOUNTING PLATE (1) over DRYWALL ANCHOR (2) and insert SCREWS (3) with #2 Phillips screwdriver. See FIGURE B below. Secure MOUNTING PLATE (1) to wall with SCREWS (3).
For installations on tiled walls without reinforcement studs,
PLATE (5), then drill two 1/4" diameter holes a minimum of 1-1/4" deep. Insert the two TILE ANCHORS (4) flush with face of the finished wall. Secure MOUNTING PLATE (1) to wall with SCREWS (3).
to locate the center of each MOUNTING PLATE (1) start at the lower left corner of cabinet frame. Measure as
TEMPLATES (A & B)
to locate the center of each MOUNTING PLATE (1), cut the template out cutting on the dotted lines.
or
DIMENSIONS
use DRYWALL ANCHORS (2) and SCREWS (3) for securing
If TILE ANCHORS (4) and SCREWS (3) are used for securing MOUNTING
to locate the four MOUNTING PLATES (1).
25-1/2"
LOWER LEFT
CORNER
OF CABINET
1-15/16"
A
1-3/32"
1
2
1
1-15/16"
Figure A
LEVEL
19-3/8"
2
3
CENTER LINE
2
4
1
Figure B
3
4
1-3/32"
NOTE; For best installation results use:
• No Anchors, Screws (3) directly secured to reinforcement studs
• TILE ANCHORS (4) for tile or plaster walls
• DRYWALL ANCHORS (2) for dry wall
1
FINISHED WALL
M968408D
Loading...
+ 2 hidden pages