American Standard 6726 User Manual

Installation

STANDARD COLLECTION

Instructions

6726

24" TOWEL BAR & GLASS SHELF

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

Recommended Tools

CARE INSTRUCTIONS:

10'

Tape Measure

24" TOWEL BAR & GLASS SHELF

The 24" TOWEL BAR & GLASS SHELF (1) works best if secured to a wall stud or cross brace within the wall, using the SCREWS (3) supplied.

If the 24" TOWEL BAR & GLASS SHELF (1) is to be installed on a tile or plaster wall the TILE ANCHORS (4) or DRYWALL ANCHORS(6) and SCREWS (3) should be used.

Determine desired height and location (optional) and mark a center line. For the 24" TOWEL BAR (2) mark a centerline 24" horizontally from the first location. Using the MOUNTING PLATE (5) as a template mark the two spots for the mounting holes. Repeat for the other MOUNTING PLATE (5). If MOUNTING PLATE (5) is secured to a stud or cross brace drill small pilot holes for SCREWS (4).

For installations on drywall,

screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with the wall. Place MOUNTING PLATE (5) over DRYWALL ANCHORS (6) and insert SCREWS (3) with #2 Phillips screwdriver. See illustration below. Secure MOUNTING PLATE (5) to wall with SCREWS (3).

use DRYWALL ANCHORS (6) and SCREWS (3) for securing MOUNTING PLATE (5) to wall. Place #2 Phillips

Drill

Regular Screwdriver

Phillips Screwdriver

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.

Certified to comply with ANSI A112.18.1 U.S. Patent No. D403,750

M968218B

For installations on tiled walls,

1/4" diameter holes a minimum of 1-1/4" deep. Insert the two TILE ANCHORS (4) flush with face of the finished wall. Secure MOUNTING PLATE (5) to wall with SCREWS (3).

For the 24" TOWEL BAR & GLASS SHELF (1), Install TOWEL BAR (2) into bottom of SUPPORT POSTS (10, 10a). Align slot in towel bar with notch in recess of support post (10, 10a) (see Figure A). Install the WASHER (11), GLASS SHELF (15), WASHER (11) onto SUPPORT POSTS (10, 10a). Install and tighten SCREWS (13). See illustration.

Install the WALL ESCUTCHEON (7) on the MOUNTING PLATES (5). Place 24" TOWEL BAR & GLASS SHELF (1) onto MOUNTING PLATES (5). Secure using SCREWS (14) and tighten.

Push INDEX BUTTONS (9) into the SUPPORT POSTS (10, 10a). See illustration.

If TILE ANCHORS (4) and SCREWS (3) are used for securing MOUNTING PLATE (5), then drill two

USE MOUNTING PLATE AS TEMPLATE

CENTER LINE

48 TO 68

24"

CENTER LINE

INCHES FROM

FLOOR

48" TO 68" (OPTIONAL)

FINISHED WALL

Figure A

10 10a

SLOT IN TOWEL BAR

NOTCH IN RECESS OF SUPPORT POST

6726 24" TOWEL BAR WITH GLASS SHELF

STANDARD

COLLECTION

ACCESSORIES

24" TOWEL BAR

WITH GLASS SHELF

MODEL NUMBERS

6726

M923031-0070A

24" GLASS SHELF

M962136-0070A

MOUNTING BRACKET

Replace the "YYY" with appropriate finish code

CHROME SATIN

002 295

M919237-YYY0A

24" TOWEL BAR

M962233-0070A

INDEX BUTTON

M962139-YYY0A

SUPPORT KIT

M907736-YYY0A

ESCUTCHEON

For toll-free information and answers to your questions, call:

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

HOT LINE FOR HELP

1-800 442-1902

Weekdays 8:00 a.m. to 8:00 p.m. EST

Weekdays 8:00 a.m. to 7:00 p.m. EST

M968218B