American Standard 605X.102, 605X.163, 605X.104, 605X.164, 605X.105 Installation Manual

...

Installation Instructions

SELECTRONIC

Proximity Faucets

Cast Spout and

Gooseneck Spout

MODEL NUMBERS

605X.102 605X.163

CAUTION: Use only American Standard

supplied cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty.

605X.104 605X.164

605X.105 605X.165

2-3

4-6

7-8

9-10

Product No.'s & Options

Specifications

Faucet Installation

Electrical Installation

Start-up / Maintenance

FAQ’s / Troubleshooting

Certified to comply with ASME A112.18.1

Installation Instructions

NOTE TO INSTALLER: Please give this manual to the customer after installation.NOTE TO INSTALLER: Please give this manual to the customer after installation.

Parts

To learn more about American Standard Selectronic® Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

M965650 Rev. 1.3 (8/15)

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure

Ins tal lati on I nstr uct ions

that your installation proceeds smoothly--please read these instructions carefully before you begin.

UNPACKING

The illustration below shows the fitting and all loose items after they have been removed from the carton. Some items may be packaged partially assembled to other items.

1. Installation Instructions

2. Cast Spout Assembly 2a. Gooseneck Spout Assembly

3. Mounting Kit

4. Control Box

5. Supply Hose 6a. DC Long Life Power Pack 6b. DC Standard Battery 6c. AC Plug-In Power Supply

How to order the Selectronic Product

1. Choose Power Supply

2. Choose Desired Spout

605X.10X

All American Standard Faucets Are Water Tested At Our Factory. Some Residual Water May Remain In The Faucet During Shipping.

6d. AC Hard-Wire Power Transfomer

7. Y-Adapter

8. 27" Extension Cable

9. 10 ft. Extension

10. 4" Deck plate (optional, must be ordered separately)

11. 8" Deck plate (optional, must be ordered separately)

12. Mixing Valve (optional, must be ordered separately)

13. Control Box Cover Screws

DC Long Life

Power Pack

6053.Series

DC Standard

Battery

6055.Series

AC Plug-in

6056.Series

AC Hardwire

6059.Series

AC Multi

6057.Series

• Single Hole Sink

• Single Inlet

Base Product Deck Plate (optional) Mixing Valve (optional)

• 1 and 3 Hole Sinks

• Single Inlet

• 1 and 3 Hole Sinks

• Hot and Cold Inlets

Base Product

DO NOT REMOVE PROTECTIVE FILM FROM SENSOR EYE UNTIL INSTALLATION IS COMPLETE.

SELECTRONIC Proximity Faucets

Cast Spout and

Goose Neck Spout

Certified to comply with ASME A112.18.1

Installation Instructions

NOTE TO INSTALLER: Please give this manual to the customer after installation.NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic® Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

605X.16X

DO NOT REMOVE PROTECTIVE FILM FROM SENSOR EYE UNTIL INSTALLATION IS COMPLETE.

MODEL NUMBERS

605X.102

605X.104

605X.163

605X.164

CAUTION: Use only American Standard

supplied cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty.

Product No.'s & Options

Specifications

Faucet Installation

Electrical Installation

Start-up / Maintenance

FAQ’s / Troubleshooting

Parts

(In Toronto Area only: 1-905-306-1093)

88 8

605X.105 605X.165

1 1

2 2

2-3 2-3

4-6 4-6

7-8 7-8

9-10 9-10

Deck Plate

605P400

Mixing Valve

605P800

605XTMV

M965650 Rev. 1.3 (8/15)

Fig. 1

Roughing-in Dimensions

141mm (5-1/2)

131mm

(5-1/8)

MOUNTING SURFACE

6-1/8"

(155mm)

(179mm)

11-1/8"

(284mm)

GENERAL DESCRIPTION:

Electronic faucet with proximity operation. Vandal resistant solid brass construction single post mounting. Operates on DC (battery/power pack) or AC permanent power (plug-in/hardwire). In-line strainer for solenoid is integral. Single inlet 3/8 compression, built-in check valves, and flexible stainless steel 16-1/4" reach inlet hose for spout connection.

Note: All plumbing and electrical wiring must be installed in accordance with applicable codes, regulations and standards.

81mm

(3-3/16)

381mm

(15)

3/8" COMP.

49mm

(2)

114mm (4-1/2)

500mm

(20")

32mm (1-1/4)

125mm

(4-7/8)

1524mm

(60)

TOOLS REQUIRED; Fig. 2

1 Slip Joint Pliers 2 Adjustable Wrench 3 Plumbers' Putty or Caulking 4 Phillips Screwdriver 5 Flat Blade Screwdriver 6 Electric Drill & 1/4" Drill Bit 7 Tape Measure

49mm

(2)

381mm

(15)

Fig. 2

CAUTION: Use only American Standard

supplied cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty.

RECOMENDED ELECTRICAL BOX OR EQUIVALENT BY OTHERS

4" (102mm) SQ. X 3-1/2" (89mm) DEEP ELECTRICAL BOX

Hubbel-RACO #256 OR EQUAL (BY OTHERS).

HARD-WIRED AND MULTI AC 10’ MAX. CABLE LENGTH

10'

INSTALLATION

INSTALL SPOUT ASSEMBLY;

Fig. 1

CAUTION

1. (Optional) Assemble DECK PLATE (1) and PUTTY PLATE (2) to FAUCET BODY (3) with SCREW (4).

2. Connect the two 27" EXTENSION CABLES (5) to

the Faucet Sensor Cables.

3. Insert 27" EXTENSION CABLES (5) , FLEX HOSE (6) and SPOUT SHANK (7) through center hole of mounting surface.

4. Assemble "C" WASHER (8) and LOCKNUT (10) onto threads of SPOUT SHANK (7) from underside of mounting surface.

5. Align FAUCET (3) and tighten LOCKNUT (10). If using DECK PLATE (1) hand tighten DECK PLATE SPIN NUTS (11) to secure FAUCET (3) to mounting surface. Fig. 1b.

Turn off hot and cold water supplies before beginning

Fig. 1

122

SENSOR CABLES

M965650 Rev. 1.3 (8/15)

MOUNT CONTROL BOX; Fig. 2

1. Determine location of CONTROL BOX (1). It must be

located with-in the 14" (356mm) by 21" (533mm) shaded area shown in Figure 2 in order for electrical connections from the spout assembly to be made.

NOTE: CONTROL BOX SUPPLY HOSE is 20". Distance between wall supply and CONTROL BOX (1) must be taken into consideration.

2. Remove tape from CONTROL BOX COVER (2) and

pull off COVER (2). Hold the CONTROL BOX (1) in desired location and mark the four mounting hole locations as shown.

NOTE: Find plastic bag containing 4 M5X16 screws to be used for securing the CONTROL BOX COVER (1) when installation is complete.

NOTE: For AC installation, make power supply connection before mounting CONTROL BOX (1) to wall.

3. It is recommended that the CONTROL BOX (1) be secured

to a wall stud or cross brace within the wall using the SCREWS (3) supplied. If the CONTROL BOX (1) is to be installed on tile or plaster walls, the ANCHORS (4) and SCREWS (3) should be used.

Fig. 2

LAVATORY RIM OR MOUNTING SURFACE

14"

SUPPLIES

WASTE

MOUNTING HOLES

(500mm)

21"

(mm)

(356mm)

1524mm

20"

(60)

(76mm)

ENCLOSURE

MOUNTING

HOLES

2-3/4"

(71mm)

3-3/4"

(96mm)

NOTE: If using Mixing Valve (optional) See Sheet #M968808 for installation instructions.

CONNECT SPOUT HOSE TO CONTROL BOX; Fig. 3

1. Connect SUPPLY NUT (1) from spout hose to nipple on

top of CONTROL BOX (2). Tighten with adjustable wrench to make a water tight connection. Fig. 3.

CONNECT WATER SUPPLY TO

CONTROL BOX AND WALL SUPPLY; Fig. 4, 4a

NOTE; If using the optional Mixing Valve See Sheet #M968808 for installation instructions.

1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on CONTROL BOX (2).

2. Connect FLEXIBLE SUPPLY HOSE (3) to SUPPLY

NUT (1) on CONTROL BOX (2). Tighten to make a water tight connection. Use two wrenches to tighten if necessary. Fig. 4.

3. Connect FLEXIBLE SUPPLY HOSE (3) directly to wall supply. Connection on FLEXIBLE SUPPLY HOSE (3) is 3/8" compression. Use adjustable wrench to tighten connection. Do not over tighten. Fig. 4a.

Note: FLEXIBLE SUPPLY HOSE (3) measures 20" from the bottom of the CONTROL BOX (2) base. If additional supply length is required, installer must purchase parts separately.

Important: If FLEXIBLE SUPPLY HOSE (3) is too long, loop to avoid kinking.

Fig. 3

Fig. 4

Fig. 4a

COLD WATER OR

TEMPERED

WALL SUPPLY

M965650 Rev. 1.3 (8/15)

+ 8 hidden pages