American Standard 6032Y1.202.XXX, 6030Y1.102.XXX, 6030Y1.202.XXX, 6032Y1.102.XXX User Manual

INSTALLATION INSTRUCTIONS

Acrylux Builder Series Bathtubs

Model 6030Y1.102.XXX Model 6030Y1.202.XXX

Model 6032Y1.102.XXX Model 6032Y1.202.XXX

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. Local building codes vary by location. Observe all local plumbing and building codes.

RECOMMENDED TOOLS AND MATERIALS

Tape Measure Saber Saw Pencil Mortar Compound (optional)

Level Safety Glasses Drill Screws, 1" Flathead, Stainless

IMPORTANT:

• Allow tub to reach room temperature before installation.

• Before you begin, locate appropriate product reference (below).

• Read installation instructions carefully before starting project.

• Keep instructions for warranty information.

6030Y1.102.XXX 6030Y1.202.XXX

6032Y1.102.XXX 6032Y1.202.XXX

59-7/8"

1521mm

STUD LAYOUT:

The American Standard Acrylux Bathtub will fit all standard 30" x 60" tub walls.

14" 356mm

6" 152mm

Drain C

60"

1524mm

Floor Cut Out

6" x 10"

(152 x 254mm)

31-1/2" 800mm

10"

254mm

8" 203mm

= stud location

30"

762mm

15"

381mm

59-7/8"

1521mm

STUD LAYOUT:

The American Standard Acrylux Bathtub will fit all standard 32" x 60" tub walls.

15" 381mm

6" 152mm

Drain C

1524mm

= stud location

(152 x 254mm)

60"

Floor Cut Out

6" x 10"

33-1/2" 851mm

10"

254mm

8" 203mm

32"

813mm

18"

457mm

LHO shown - reverse for RHO LHO shown - reverse for RHO

754281-100 Rev. A

INSTALLATION INSTRUCTIONS

STEP 1. PREPARING ALCOVE

• Strip to bare studs.

• Alcove studs should be constructed as shown above.

• Floor must be clean, smooth, and level (check with level). Sub floor must be installed. Do not install tub on open floor joists.

• Cut hole in sub floor as shown on page 1 to accommodate drain.

STEP 2. INSTALLING TUB

• Trial fit tub in prepared alcove. With tub sitting flat on floor, check with level on top of tub. Tub should be level from front-to-back and side-to-side (Fig 1).

• A floor leveling compound (smooth mortar) or a similar quick-setting compound specifically made for leveling floors may be used to fully support and level base.

• After tub is leveled, if alcove is larger than tub, shim between tub and studs to create a tight fit. Screw tub flange to studs (Fig. 2).

CLEANING

FIGURE 1. Check to assure tub is level.

FIGURE 2. If necessary, shim between tub and studs for

tight fit and screw to each stud.

• Do not use any abrasive cleaners or metal scrapers.

• If drywall mud or plaster gets on your shower, it may be carefully removed with a wooden scraper made from a piece of scrap wood.

• Adhesive may be removed with mineral spirits.

• Ideal cleaners are Soft Scrub Gel® or Comet Gel®.

WARNING:

Some cleaning products are not suitable for use. Read all labels carefully. DO NOT USE if they say “not suitable for use with ABS, acrylic, or polystyrene.

754281-100 Rev. A-2-

+ 1 hidden pages