American Standard 6032Y1.118.XXX, 6030Y1.218.XXX, 6030Y1.118.XXX, 6030Y2A.118.XXX, 6032Y1.218.XXX User Manual
...
INSTALLATION INSTRUCTIONS
Acrylux Builder Series Whirlpools
Model 6030Y2A.118.XXX
Model 6030Y2A.218.XXX
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please
read these instructions carefully before you begin. Local building codes vary by location. Observe all local plumbing and building codes.
Model 6030Y1.118.XXX
Model 6030Y1.218.XXX
Model 6032Y1.118.XXX
Model 6032Y1.218.XXX
RECOMMENDED TOOLS AND MATERIALS
Tape Measure Mortar Compound (optional) Pencil Saber Saw
Safety Glasses Screws, 1" Flathead, Stainless Drill Level
IMPORTANT:
• Read installation instructions carefully before starting project.
• Before you begin, locate appropriate product reference (below).
• Allow tub to reach room temperature before installation.
• Water test tub before installation.
• Keep instructions for warranty information.
6030Y2A.118.XXX
6030Y2A.218.XXX
1"
25mm
18"
457mm
30"
762mm
59-7/8"
1521mm
19"
483mm
Motor / Pump
Access Cover
STUD LAYOUT:
The American Standard Acrylux Bathtub
will fit all standard 30" x 60" tub walls.
14"
356mm
6"
152mm
Drain C
L
Floor Cut Out 6" x 10"
(152 x 254mm)
1524mm
= stud location
60"
31-1/2"
800mm
10"
254mm
8"
203mm
GFI Electrical
Outlet
6030Y1.118.XXX
6030Y1.218.XXX
STUD LAYOUT:
The American
Standard Acrylux
Whirlpool will fit all
standard 30" x 60"
tub walls.
= stud location
59-7/8"
1521mm
31-1/2"
800mm
10"
254mm
8"
203mm
6032Y1.118.XXX
30"
762mm
15"
381mm
Motor / Pump
Access Cover
14"
356mm
6"
152mm
Drain C
L
Floor Cut Out 6" x 10"
(152 x 254mm)
60"
1524mm
GFI Electrical
Outlet
Left-hand drain shown - reverse layout for right-hand drain.
Subject to manufacturing tolerance of [+] or [-] 1/8"
6032Y1.218.XXX
STUD LAYOUT:
The American
Standard Acrylux
Whirlpool will fit all
standard 32" x 60"
tub walls.
= stud location
1521mm
33-1/2"
851mm
59-7/8"
12"
305mm
8"
203mm
32"
813mm
Motor / Pump
Access Cover
15"
381mm
6"
152mm
Drain C
L
Floor Cut Out 6" x 12"
(152 x 305mm)
60"
1524mm
GFI Electrical
Outlet
18"
457mm
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2008
754282-100 Rev. A
INSTALLATION INSTRUCTIONS
STEP 1. PREPARING ALCOVE
• Alcove studs should be constructed as shown.
• Floor must be clean, smooth, and level (check with level). Sub floor must be
installed. Do not install tub on open floor joists.
• Cut hole in sub floor as shown, to accommodate drain.
• Access panels must be located on both ends of whirlpool alcove to service
pump/motor and drain assembly after installation. Failure to provide access
to these areas may result in added removal and re-installation costs in the
event service may be required.
STEP 2. ELECTRICAL CONNECTIONS
• Install a 110 volt, 20 amp duplex outlet to the stud wall underneath the
whirlpool at least 4" (102mm) above the sub floor. (Figure 1)
• Motor/pump must have a separate 110 volt, 20 amp service from the breaker
panel to the motor/pump location. Do not combine any other electirc service
with whirlpool supply line.
• Service supply line must be connected to a ground fault interrupter (GFI) at
the breaker panel for added protection and to meet code requirement. Install
breaker after all other electrical connections have been made.
• Your whirlpool wiring should be installed by a licensed electrician. All
electrical preparation and connections must be made in strict compliance
with local and national electrical codes.
WARNING: If whirlpool is not properly wired, there
is danger of electrical shock or fire.
4"
102mm
Wire to ground
fault interrupter
FIGURE 1. Locate receptacle in same end of alcove
as motor.
STEP 3. LEAK TEST WHIRLPOOL
• Water test tub in area where all fittings and connections can be
inspected.
• Fill tub with water, make sure water is above jets. Run for 10 minutes.
Inspect all fittings, plugs and connections for possible leaks.
• Drain tub. If any leaks are found, call American Standard Customer Service
Department at 1-800-442-1902.
STEP 4. INSTALLING WHIRLPOOL
• Install drain, waste and overflow.
• Trial fit whirlpool in prepared alcove. With whirlpool sitting flat on floor, check
with level on top of tub. Whirlpool should be level from front to back and side
to side (Figure 2). If tub is not level, remove tub and level floor using leveling
compound.
• A floor leveling compound (smooth mortar) or a similar quick-setting
compound specifically made for leveling floors may be used to fully support
and level tub.
• If alcove is larger than tub, shim between tub and studs to create a tight fit.
Screw tub flange to studs. (Figure 3)
• Connect drain piping to drain.
FIGURE 2. Check to assure tub is level.
FIGURE 3. If necessary, shim between tub and
studs for tight fit and screw to each stud.
754282-100 Rev. A-2-
Loading...