American Standard 6032 TUB, 6032 Seated Shower Base User Manual

INSTALLATION INSTRUCTIONS

6032 SERIES TUB 6032 SERIES SEATED SHOWER BASE

HIGH GLOSS ACRYLIC SURFACE

Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

BEFORE YOU BEGIN....

Local building codes vary by location. Observe all local plumbing and building codes. Your new bath is shipped to you after careful inspection. To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

TOOLS & MATERIALS REQUIRED

TOOLS:

• Level

• Square

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

NOTE: Take extra care in handling surfaces of the bath. Use only non-abrasive cloths to avoid scratching.

• Screw Driver

• Standard Woodworking Tools

• Personal Safety Equipment

• Caulking Gun

MATERIALS:

• Nails

• Plumber’s Putty

• Silicone Sealant

• 1 x 3 or 2 x 4 Stringers

• Drop Cloth

• Mortar Mix or Grout

ROUGH-IN INFORMATION: 6032 SERIES TUB

(1524mm)

15-5/8"

(397mm)

32"

(813mm)

3-3/16"

(81mm)

9-3/4"

(248mm)

2" (51mm)

C/L OF DRAIN

17-3/4"

(451mm)

STRINGER

HEIGHT

60"

3-15/16" (100mm)

3" (76mm)

3-3/16"

(81mm)

18"

(457mm)

1" (25mm)

4-1/16"

(103mm)

ROUGH-IN INFORMATION: 6032 SERIES SEATED SHOWER BASE

60"

(203mm)

1-1/8"

(29mm)

18-3/4" (476mm)

STRINGER HEIGHT

14-7/8"

(378mm)

(1524mm)

3-1/2" (89mm)

(483mm)

19"

1" (25mm)

15-5/16"

(389mm)

SEAT HT.

1-3/8" (35mm)

15-5/8" (397mm)

(651mm)

1-1/8" (29mm)

25-5/8"

31-1/4"

(794mm)

5" (127mm)

THRESHOLD HT.

SAVE FOR FUTURE USE

GENERAL SPECIFICATIONS FOR 6032 TUB

INSTALLED SIZE

WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA)

PTS. CUBE (FT

)

22 x 44.5 In. (559 x 1130mm)

25 X 53 In.(635 x 1346mm)

37 Lbs./Sq.Ft. (181 Kgs/Sq.m)

60 x 32 x 18 In.

(1524 x 813 x 457mm)

60 Lbs. (27 Kg)

493 Lbs.(224 Kg)

52 Gal. (197 L)

12 In. (305mm)

27.5

28.9

GENERAL SPECIFICATIONS FOR 6032 SHOWER BASE

INSTALLED SIZE

WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS. CUBE (FT

60 x 32 x 19 In.

(1524 x 813 x 483mm)

60 Lbs. (27 Kg)

<15 Lbs./Sq.Ft. (<75 Kgs/Sq.m)

)

N/A N/A N/A N/A

N/A

27.5

29.4

754731-100 Rev. D

GENERAL INSTALLATION INFORMATION ...

1. BATH MAY ONLY BE INSTALLED IN A RECESS TYPE INSTALLATION.

2. THIS BATH IS NOT SELF-SUPPORTING AND MUST BE SUPPORTED ALONG ITS ENTIRE BOTTOM WITH MORTAR OR GROUT. STRINGERS WILL HELP LEVEL TUB, BUT WILL NOT PROVIDE ADEQUATE SUPPORT.

3. TAKE EXTRA CARE WHEN DRIVING NAILS OR SCREWS TO AVOID DAMAGING THE BATH.

INSTALLATION AND FRAMING INSTRUCTIONS:

A.) Locate studs as required. Ensure roughing-in dimensions are proper, plumb, and square. It is strongly recommended that

an additional opening be provided for access to the drain components.

ILLUSTRATION 1

Each alcove stud must be plumb and square.

B.) As shown in ILL. 2, mark the position of the underside of the deck by tracing a line onto the studs at the height indicated, using a level or other suitable straight edge.

C.) With the top of the stringer touching the traced line, attach the stringer to the studs.

ILLUSTRATION 2

6032 Series Tub

6032 Series Seated Shower Base

DIM A

STRINGER HEIGHT

17-3/4" (451mm)

18-3/4" (476mm)

DIM B

STRINGER LENGTH

30-1/2" (775mm)

29-3/4" (756mm)

D.) Install drain components to the bath following the manufacturer's instructions. See the roughing-in drawing for suggested opening size and location dimensions.

754731-100 Rev. D

+ 2 hidden pages