American Standard 5065.040, 5065.010 User Manual

TRADITIONAL BIDET

660mm

(26)

413mm (16-1/4)

76mm (3)

102mm

(4)

178mm

(7)

140mm

(5-1/2)

394mm (15-1/2)

178mm

(7)

3/8 FLEX C.W.T.

SUPPLIES FROM

FITTING

1-1/4 O.D. TAILPIECE

(FOR THRU FLOOR

TRAPPING ONLY)

1-1/4 O.D. TAILPIECE

(FOR WALL DRAIN

OUTLET ONLY)

1-1/4 O.D. WASTE OUTLET

3/8 N.P.T.

SUPPLIES

C/L OF BIDET

406mm

(16)

FOOT

OUTLINE

OFFSET

WASTE

C/L

268mm (10-1/2)

127mm

(5)

76mm

(3) MIN.

29mm (1-1/8)

286mm (11-1/4)

VIEW "A" - "A" (WALL SUPPLIES/OUTLET DETAIL)

29mm (1-1/8) OFFSET

"A"

FINISHED

WALL

FINISHED

FLOOR

FINISHED

FLOOR

1-3/4 DIA.

DRAIN OUTLET

165mm

(6-1/2)

OVERFLOW

10mm (3/8) DIA.

MTG. HOLES (2) ON

178mm (7) CTRS

203mm

(8)

SPRAY

102mm

(4)

❑ 5065.040 For deck-mounted tting (illustrated)

• Vitreous china

• Flushing rim and vertical cleansing spray

• Design matched to Reminiscence and Eneld toilets

• Two bolt caps

• Integral overow

Shown with 8391.000 Amarilis bidet tting with

0000.452 Jasmine metal cross handles (not included)

❑ 5065.010 For over-the-rim tting

• Vitreous china

• Punched for single hole, over-the-rim tting, less ushing rim and spray

• Design matched to Reminiscence and Eneld toilets

• Integral overow

• Two bolt caps

TRADITIONAL BIDET

VITREOUS CHINA

Nominal Dimensions:

600 x 406 x 394mm (26" x 16" x 15-1/2")

Compliance Certications Meets or Exceeds the Following Specications:

• ASME A112.19.2M for Vitreous China Fixtures

To Be Specied:

❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Silver ❏ Fawn Beige ❏ Black

❏ Bidet Fitting*: ❏ Fitting Finish: ❏ Trap: ❏ Supplies with Stops:

* See faucet section for additional models available

NOTES:

DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES ARE SUGGESTED.

▲ WALL OUTLET INSTALLATION REQUIRES:

- A TRUE 1-1/4" BODIED “P” TRAP,; DO NOT USE A UNIVERSAL 1-1/4 X 1-1/2" TRAP.

- WALL OUTLET INSTALLATION.

- DRAIN TAILPIECE MUST BE CUT TO 1-1/2" LENGTH FOR WALL OUTLET CONNECTION.

■ THRU-FLOOR OUTLET INSTALLATION (ALTERNATE).

“P” TR AP AND FIT TINGS NOT FURNISHED WITH BIDET AND MUST BE ORDERED SEPARATELY. BIDET FIT TING HAS TR ANSFER VALVE FEATURE.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to c hange or cancellation. No responsibility is assumed for use of superseded or voided leaet.

Revised 2/08