American Standard 4968.300 Installation Manual

INSTALLATION
INSTRUCTIONS
ESTATE
®
PULL-DOWN KITCHEN FAUCET
Thank you for selecting American Standard... the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
4968.300
Certied to comply with ANSI A112.18.1M
Certied to comply with ANSI A112.18.1M
Plumbers' Putty or CaulkingAdjustable WrenchPhillips ScrewdriverFlat Blade Screwdriver
1
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
CAUTION
Turn off hot and cold water supplies before beginning.
(A) Installation less ESCUTCHEON (1). Make certain the SEAL (9) is properly seated in recess of faucet body. Insert supply HOSES (2), SPRAY HOSE (7) and SHANK (3) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.
(B) Installation with ESCUTCHEON (1 Optional). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1). Make certain the SEAL (9) is properly seated in recess of faucet body. Insert SUPPLY HOSES (2), SPRAY HOSE (7) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface. Follow mounting instructions below to secure faucet to mounting surface.
Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6).
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening the screws slightly each time until all are snug to ensure even pressure.
7
7
B (Optional) A
SPOUT BASE
Product names listed herein are trademarks of AS America, Inc. © AS America, Inc. 2016
9
1
3
7
5
6
2
4
8
PUTTY
MOUNTING
SURFACE
SINK OR
- 1 -
SPOUT BASE
9 3 2
7
5
6
4
8
M965743 (6/16)
2
MAKE WATER SUPPLY CONNECTIONS
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLY HOSES (1, 2) directly to wall
supplies. Connection on tting supplies are 3/8" compression. Connect left supply hose (Red Stripe) to Hot wall supply. Connect right supply hose (Blue Stripe) to Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten.
Faucet supplies are 32 " long from faucet base.
*
Note: If additional supply length is required, installer must purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are too long, loop as illustrated to avoid kinking.
3
CONNECT SPRAY HOSE AND INSTALL WEIGHTS
RED
STRIPE
HOT
BLUE
STRIPE
2
COLD
1
Push the SPRAY HOSE END (1) into the HOSE CONNECTOR (2) and slide down the LOCKING COLLAR (3) until it snaps into place.
With HAND SPRAY (4) seated in SPOUT (5), install WEIGHT (6) at labeled area on HOSE (7), secure with SCREW (8).
4
TEST INSTALLED FAUCET
• Turn ON water at main supply.
With HANDLE (1) in “off” position, unthread SPRAY (3) from HOSE (2).
Operate handle back to front, in COLD and HOT positions, to ush water
lines thoroughly.
Replace SPRAY (3) onto HOSE (2).
SPRAY OPERATION
5
4
2
1
3
8
6
7
2
3
REMOVE
OFF
COLD
HOT
• With FAUCET on, press TOGGLE BUTTON (4) on SPRAY (3) to switch from stream to spray.
Press and hold PAUSE BUTTON (5) to temporarily stop ow from SPRAY
ON
1
(3). Release PAUSE BUTTON (5) to resume ow from SPRAY (3).
5
3
STREAM (AERATOR)
4
SPRAY
- 2 -
M965743 (6/16)
Loading...
+ 3 hidden pages