American Standard 4932.300 Installation Manual
INSTALLATION
INSTRUCTIONS
EDGEWATER
™
Single Control Kitchen Faucet
With Pull Down Spray
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
4932.300
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
1
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
• (A) Installation with ESCUTCHEON (1). (Escutcheon is not supplied with base product). Apply a bead of putty to bottom
edge of ESCUTCHEON with PUTTY PLATE (1). Make certain the SEAL (9) is properly seated in recess of faucet body. Insert
SUPPLY HOSES (2), SPRAY HOSE (7) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting
surface. Follow mounting instructions below to secure faucet to mounting surface.
• (B) Installation less ESCUTCHEON (1). Make certain the SEAL (9) is properly seated in recess of spout base. Insert supply
HOSES (2), SPRAY HOSE (7) and SHANK (3) through mounting hole and seat spout base onto sink or mounting surface.
Do not use putty.
• Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).
• Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside of sink
or mounting surface. Hand tighten LOCKNUT (6).
• Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening the screws
slightly each time until all are snug to ensure even pressure.
Certied to comply with ANSI A112.18.1M
Plumbers' Putty or CaulkingAdjustable WrenchPhillips ScrewdriverRegular Screwdriver
CAUTION
Turn off water at
main supply
A
(OPTIONAL)
SPOUT BASE
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2016
7
9
3
7
5
6
2
4
8
1
PUTTY
SINK OR
MOUNTING
SURFACE
- 1 -
B
SPOUT BASE
7
9
3
2
7
5
6
4
8
M965717 Rev. 1.0 (4/16)
2
MAKE WATER SUPPLY CONNECTIONS
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLY HOSES (1, 2) directly to wall
supplies. Connection on tting supplies are 3/8"
compression. Connect left supply hose (Red Stripe) to Hot
wall supply. Connect right supply hose (Blue Stripe) to Cold
wall supply. Use adjustable wrench to tighten connections.
Do not over tighten.
Faucet supplies are 21" long from faucet base.
*
• Note: If additional supply length is required, installer
must purchase additional parts separately.
• Important: If SUPPLY HOSES (1, 2) are too long,
loop as illustrated to avoid kinking.
3
CONNECT SPRAY HOSE & INSTALL WEIGHTS
• Push the SPRAY HOSE END (2) into the HOSE CONNECTOR
(1) slide down LOCKING COLLAR (3) until it snaps into place
to secure connection.
• With HAND SPRAY (4) seated in SPOUT (5), install WEIGHT (7)
onto HOSE (6) 21 inches from the underside of the sink deck
and secure with SCREW (8).
• Adding SECOND WEIGHT (9) is optional.
• With one weight, spray will retract and dock potentially
requiring slight assistance.
• With two weights, spray will retract and dock automatically
once released.
• Please add the SECOND WEIGHT (9) below the initial
WEIGHT (7).
BLUE
RED
STRIPE
HOT
1
STRIPE
2
COLD
5
4
4
CHECK CONNECTIONS FOR LEAKS
• Move HANDLE into “off” position.
• Turn on water supplies and check connections for leaks.
• Operate HANDLE (1) up and down, left and right to
ushwater lines thoroughly.
• Operate HAND SPRAY and check connections for leaks.
CHECK CONNECTIONS
FOR LEAKS
- 2 -
8
7
6
9
(Optional)
21"
(610 mm)
1
2
3
M965717 Rev. 1.0 (4/16)
Loading...