American Standard 4901.380 Installation Manual

INSTALLATION
INSTRUCTIONS
AVERY
ELECTRONIC PULL-DOWN KITCHEN FAUCET
Thank you for selecting American Standard... the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
RECOMMENDED TOOLS
Flat Blade Screwdriver Adjustable WrenchPhillips Screwdriver
4901.380
Certied to comply with ANSI A112.18.1M
1
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
CAUTION
Turn off water at main supply
(A) Installation on 1-hole mounting surface: (please refer to template provided)
From below: Insert CABLES (12) and HOSES (3) through RUBBER WASHER (6), BRASS WASHER (7), and threaded LOCKNUT (8).
Assemble RUBBER WASHER (6), BRASS WASHER (7), and threaded LOCKNUT (8) onto SHANK (5) from underside of sink or mounting surface. Hand tighten LOCKNUT (8).
Make sure faucet is aligned properly with handle on the right and logo facing directly forward.
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (8). Work your way around LOCKNUT (8), tightening the screws
slightly each time until all are snug to ensure even pressure.
(B) Optional: Installation on 3-hole mounting surface: Requires Deck Escutcheon - order separately
Make certain the SEAL (12) is properly seated in bottom recess of FAUCET (2) and FOAM SEAL (13) is properly seated in bottom recess of DECK ESCUTCHEON (1). Do not use putty. (Please refer to the template provided)
Screw in two THREAD RODS (14) onto bottom of DECK ESCUTCHEON (1).
Place deck escutcheon over mounting holes of the deck.
Insert SUPPLY CABLES (11), HOSES (3), SPRAY HOSE (4) and SHANK (5) through hole of DECK ESCUTCHEON (1) and
mounting surface.
Follow mounting instructions above to secure faucet to mounting surface. Thread the MOUNTING NUTS (10) to secure DECK ESCUTCHEON.
Product names listed herein are trademarks of AS America, Inc. © AS America, Inc. 2017
A
SPOUT BASE
4
7
8
5
- 1 -
B (OPTIONAL)
2
12
11
3
6
9
SINK OR
MOUNTING
SURFACE
SPOUT BASE
14
10
5
4
7
8
M965802 Rev.1.1 (7/17)
12
1 13
3
6
9
2
MAKE WATER SUPPLY CONNECTIONS
• Turn off hot and cold water supplies before beginning.
Install INLINE FILTER (3) on each wall supply outlet. Be sure that INLINE FILTER (3) is inserted in the correct direction. (See Illustration)
Connect FLEXIBLE SUPPLY HOSES (1, 2) directly
to INLINE FILTER (3). Connection on tting supplies are 3/8" compression. Connect left supply hose (Red Stripe) to Hot wall supply. Connect right supply hose (Blue Stripe) to Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten.
Faucet supplies are 35" long from faucet base.
*
Note: If additional supply length is required,
installer must purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are too long,
loop as illustrated to avoid kinking.
3
CONNECT SPRAY HOSE AND SOLENOID ASSEMBLY, AND INSTALL WEIGHT
• Push the SPRAY HOSE END (1) into FEMALE ADAPTER
(2) and slide down locking collar to secure connection.
Orient solenoid valve with the orientation label facing up.
Push SOLENOID ASSEMBLY (3) connection “B” into the
HOSE CONNECTOR (4) as shown, and slide down locking collar towards SOLENOID ASSEMBLY (3) to secure connection.
Push SOLENOID ASSEMBLY (3) connection “A” into
other end of FEMALE ADAPTER (2) as shown, and slide locking collar towards SOLENOID ASSEMBLY (3) to secure connection.
With HAND SPRAY (5) seated in SPOUT (6), install
WEIGHT (7) at labeled area onto HOSE (8), secure with SCREW (9).
Important: Make sure you pull out hose and check to
see that it moves freely and is not obstructed by supply hoses, solenoid valve or items in the bottom of the cabinet.
(3) INLINE
FILTER
6
5
HOT
1
3
IMPORTANT: Do not use sealent on threads
2
COLD
Slide locking collar to secure
UP
Locking Collar
- 2 -
4
B
3
A
18"
2
1
9
7
8
M965802 Rev.1.1 (7/17)
Loading...
+ 4 hidden pages