American Standard 4770.702 SER., 4770.722, 4770.712 SER., 4771.222, 4770.732 User Manual
...
Installation
Instructions
TOP MOUNT
KITCHEN FAUCETS
4770.702 SER.
4770.712 SER.
4770.722 SER.
4770.732 SER.
4771.702 SER.
4771.712 SER.
4771.722 SER.
4771.722 SER.
4771.222 SER.
4771.322 SER.
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
INDEX
CAP
PORCELAIN
CROSS
HANDLE
HANDLE
SCREW
WASHER
INDEX
CAP
METAL
CROSS
HANDLE
HANDLE
SCREW
Certified to comply with ANSI A112.18.1M
U.S. Patent No. 5,819,789
INDEX CAP
M968145D
PORCELAIN
LEVER
HANDLE
AERATOR
SPRAY
LOCKNUT
SUPPLY
NUT
CAP
HANDLE BASE
(CROSS HANDLE)
HANDLE BASE
(LEVER HANDLE)
ADAPTER
CARTRIDGE
SPRAY
AND HOSE
SPRAY
HOLDER
WING
NUT
METAL
LEVER
HANDLE
HANDLE
SCREW
END
CAP
INSTALL FAUCET
1
CAUTION
Turn off hot and cold water supplies before beginning.
Screw SPOUT onto BODY.
Place faucet in position on sink.
Assemble and tighten LOCKNUTS from underside of SINK.
Connect the HOT water supply to the left SHANK and the
COLD water supply to the right SHANK using sealant,
appropriate connectors, and COUPLING NUTS.
To install SPRAY:
Unscrew SPRAY CAP.
Place the HOLDER into the appropriate mounting hole.
Assemble the SPRAY HOLDER WING NUT onto the shank
of SPRAY HOLDER from below and tighten.
Feed SPRAY HOSE through HOLDER so SPRAY sits in HOLDER.
From underneath sink, attach COUPLING NUT of SPRAY HOSE
to HOSE SHANK. Tighten COUPLING NUT firmly.
SINK
BODY
PUTTY
HOSE
SHANK
HOT
COLD
SPRAY
CAP
SPRAY
HOLDER
WING
NUT
LOCKNUT
TEST INSTALLED FAUCET
2
Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
SERVICE Handle alignment.
3
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Pull out INDEX CAP and remove
HANDLE SCREW.
Pull off HANDLE BASE and remove
ADAPTER.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90° and replace.
Replace SPRING CLIP.
Reinstall HANDLE.
STOP
WASHER
90°
SPRING
CLIP
Operate both handles to flush water lines thoroughly.
Operate SPRAY (if present).
Turn handles into OFF position and replace AERATOR.
Check alignment, if not satisfactory
aligned;
Push out ADAPTER carefully.
Turn ADAPTER either 45˚ or 90˚
so that male square on
ADAPTER catches different
female square in HANDLE BASE.
Assemble and tighten
MOUNTING SCREW.
Push INDEX CAP in top of
HANDLE.
SPRAY
HOSE
COUPLING
NUT
SPRAY HOSE
COUPLING NUT
FEMALE SQUARE
IN HANDLE BASE
HANDLE
ADAPTER
SQUARE
VALVE
STEM
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90°.
Product names listed herein are trademarks of American Standard Inc.
C
American Standard Inc. 1998
For toll-free information and answers to your questions, call:
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
HOT LINE FOR HELP
1 (800) 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
Weekdays 8:00 a.m. to 7:00 p.m. EST
M968145D
Loading...