American Standard 4433.001 User Manual
Installation
Instructions
QUINCE™
4433.001
SINGLE CONTROL KITCHEN
FAUCET WITH CAST SPOUT
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended tools
Regular Screwdriver
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
1
Make certain the SEAL (9) is properly seated in recess of spout base.
(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Insert supply HOSES (2) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface.
Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1). Insert all HOSES (2) and SHANK (3) through MOUNTING RING (10) and
mounting surface. Do not use putty.
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
Phillips Screwdriver
Adjustable Wrench
CAUTION
Certified to comply with ANSI A112.18.1M
M965115_Rev.1.1
Plumbers' Putty or Caulking
Turn off hot and cold water
supplies before beginning.
PUTTY
7
7
AB
9
1
10
9
3
2
2
3
SINK OR
4
MOUNTING
SURFACE
5
8
6
8
4
5
6
MAKE WATER SUPPLY CONNECTIONS
2
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply to Hot (Marked with a Red Line)
and right supply to Cold wall supply. Use
adjustable wrench to tighten connections.
Do not over tighten.
2
1
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is
required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
INSTALL SPRAY HOLDER
3
On model with separate spray, place the SPRAY HOLDER (1)
into the appropriate mounting hole. Assemble the SPRAY
HOLDER WING NUT (2) onto the shank of SPRAY HOLDER (1)
from below and hand tighten. Do not use putty.
For installation less spray, cap off SPRAY HOSE
CONNECTION (3) with PIPE CAP (4).
CONNECT HOSE SPRAY
Feed SPRAY HOSE (5) through SPRAY
HOLDER (1) and attach COUPLING NUT (6)
of HOSE (5) to SPRAY HOSE CONNECTION (3)
on valve body. Tighten COUPLING NUT (6)
firmly.
SPRAY HOSE
CONNECTION
COLD
HOT
1
5
3
2
4
6
TEST INSTALLED FAUCET
4
Move HANDLE down into "off" position and remove
AERATOR (1).
Turn on water supplies and check connections for leaks
Operate HANDLE (2) up and down, left and right to flush
water lines thoroughly.
For faucet with spray, direct SPRAY HEAD (3) into sink and
activate SPRAY (3). Check hose connections for leaks.
Move HANDLE (2) down to "off" position and replace
AERATOR (1).
2
3
.
1
CHECK CONNECTIONS
FOR LEAKS
M965115_Rev.1.1
Loading...