Page 1
Installation
THE
COLLECTION
by
™
Instructions
4210
SINGLE CONTROL KITCHEN
PULL-OUT FAUCET
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
Certified to comply with ANSI A112.18.1M
read these instructions carefully before you begin.
TOOLS REQUIRED
Regular Screwdriver
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
1
CAUTION
(A) Installation with ESCUTCHEON (1).
Insert supply HOSES (2) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface.
Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1).
SHANK (3) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.
Turn off hot and cold water supplies before beginning.
Phillips Screwdriver
Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Discard ESCUTCHEON with PUTTY PLATE (1). Insert supply HOSES (2) and
Adjustable Wrench
Plumbers' Putty or Caulking
M968461B
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
7
A
SPOUT BASE
B
7
1
3
PUTTY
2
2
3
SINK OR
4
MOUNTING
SURFACE
5
4
5
8
6
8
6
Page 2
MAKE WATER SUPPLY CONNECTIONS
2
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply to Hot (Marked with a Red Tag)
and right supply to Cold wall supply. Use
adjustable wrench to tighten connections.
Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is
required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
CONNECT SPRAY HOSE
3
Slide COUPLING NUT (1) onto HOSE (2)
Place WASHER (3) into COUPLING NUT (1)
on HOSE (2). Thread COUPLING NUT (1) onto
HAND SPRAY (4) and tighten.
(May already be assembled).
RED TAG
1
RED
COLD
HOT
3
1
2
6
5
4
Feed small end of HOSE (2) through BODY (5) so
HAND SPRAY (4) rests inside SPRAY HOLDER (6).
Thread HOSE END (7) onto OUTLET HOSE ADAPTER (8)
and tighten.
With HAND SPRAY (4) seated in SPRAY HOLDER (6),
install WEIGHTS (9) onto HOSE (2) using two SCREWS (10).
Locate the WEIGHTS (9) two feet (2') from the underside of
the sink deck. Tighten SCREWS (10) firmly.
TEST INSTALLED FAUCET
4
Move HANDLE (1) down into "off"
position.
Turn on water supplies.
Check connections for leaks. (See
Section 5)
With HANDLE (1) down in "off"
position.
Pull HAND SPRAY (2) from FAUCET (5)
and disconnect HAND SPRAY (2). Be
careful not to lose WASHER (7). Pull
HOSE (3) (HOSE should pull
approximately 2 feet) and direct open
HOSE END (4) into sink.
6
1
2
7
3
5
2
24"
8
7
9
Operate handle up and down, in COLD and HOT positions, to
flush water lines thoroughly.
Place WASHER (7) into HOSE END (4) and connect
HAND SPRAY (2) to HOSE END (4). Place HAND SPRAY (2)
back into faucet.
Check HAND SPRAY (2) operation:
10
2
With faucet on push front of BUTTON (6) for a broad
cleansing spray.
4
M968461B
Page 3
CHECK CONNECTIONS FOR LEAKS.
5
Move HANDLE down into "off" position.
Turn on water supplies and check connections for leaks
.
Operate HANDLE (2) up and down, left and right to flush
water lines thoroughly.
Operate HAND SPRAY and check connections for leaks.
SERVICE
6
If faucet drips, operate HANDLE several times from "off" to "on." Do not
apply excessive force.
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
Pull off ESCUTCHEON CAP (4). Unscrew three MOUNTING SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8).
Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
Place SEALS (8) into CARTRIDGE PORTS (6A).
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING
SCREWS (5) alternately.
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE
SCREW (1) and install INDEX BUTTON (2).
CHECK CONNECTIONS
FOR LEAKS
RED
2
1
3
4
5
HOT LIMIT SAFETY STOP ADJUSTMENT
By restricting handle rotation and limiting the amount of hot water allowed
to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental
scalding. To set the maximum hot water temperature of your faucets, all you
need to do is adjust the setting on the HOT LIMIT SAFETY STOP.
Remove HANDLE BUTTON (1) and loosen SET SCREW (2). Pull
HANDLE (3) off valve stem. Pull off CAP (4). Use a flat blade
screwdriver or your fingers to pull up and rotate red HOT LIMIT
SAFETY STOP (5). Follow Step "A" or "B" to adjust min./max.
discharge temperature. "0" being the hottest to "7" the coldest
temperature setting. Factory set at "0".
PRY RED RING FORWARD
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten
HANDLE SCREW (1) and install INDEX BUTTON (2).
TEMPERATURE
SETTING NUMBERS
"B"
"B"
"B"
CARE INSTRUCTIONS
7
PRY RED RING FORWARD
AND ROTATE CLOCKWISE
ADJUSTMENT WHEN
WATER IS TOO COLD
To keep your new faucet looking new, please follow
these simple care instructions:
DO: Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing acids,
polish abrasives, or harsh cleaners or soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
6
6A
8
7
"A"
AND ROTATE COUNTER-
CLOCKWISE ONE CLICK
"A"
0
1
2
3
4
5
6
7
"A"
ADJUSTMENT WHEN
WATER IS TOO HOT
6
5
"RED RING"- HOT
LIMIT SAFETY STOP
Remove as much surface dirt and film using clear
water and soft cotton cloth (as described).
Use any of the following to remove tough surface
film and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and
and blot dry
with a cotton cloth.
Failure to follow these care instructions may
damage the faucet's finish.
M968461B
Page 4
M962294-0070A
BUTTON AND
SCREW KIT
M962295-YYY0A
HANDLE KIT
A907086-YYY0A
ESCUTCHEON CAP
M901142-YYY0A
BODY
SINGLE CONTROL KITCHEN
023527-0070A
CARTRIDGE SCREWS
023529-0070A
CARTRIDGE
A912746-0070A
O-RING
M918504-0070A
SCREW
PULL-OUT FAUCET
MODEL NUMBERS
4210
M952234-YYY0A
PULL-OUT SPRAY
M953052-0070A
FLOW REGULATING
CHECK VALVE
A922804-0070A
SPRAY HOLDER
M962301-0070A
INTERNAL BODY
AND SEAL
M962299--YYY0A
ESCUTCHEON AND
PUTTY PLATE
Replace the "YYY" with
appropriate finish code
CHROME
SATIN
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2004
002
295
For toll-free information and answers to your questions, call:
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 8:00 p.m. EST
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-12-00
M962146-0070A
MOUNTING KIT
HOT LINE FOR HELP
1-800 442-1902
M962302-0020A
SPRAY HOSE
AND SEAL
A953051-0070A
CHECK VALVE
A911714-0070A
SEAL WASHER
050448-0070A
WEIGHTS
M968461B
Loading...