American Standard 3573.002, 3573.018WC User Manual

GREEN TEA™ 6' X 36" WHIRLPOOL

❏ 3573.018WC Whirlpool featuring System I

• Acrylic with  berglass reinforcement

• Pre-leveled tub bottom

• Form- tted backrest position

• Raised neck support

• Dual, molded in arm rests

• 2.1 HP single speed, self-draining pump/motor

• Factory installed power cord with plug

• Ten multi-directional and  ow-adjustable jets

• Side-mounted air switch On/Off

• Can be under-mount installed

• Two silent air volume controls

• Quick Connect Safe-T-Heater connection system

• Factory installed and tested whirlpool system

• EverClean™ whirlpool system

❏ 3573.002 Bathing Pool

• Same as above without whirlpool system

GREEN TEA™ 6' x 36"

WHIRLPOOL AND BATHING POOL

HIGH GLOSS

Nominal Dimensions:

1829 x 914 x 533mm (72" x 36" x 21")

Compliance Certi cations Meets or Exceeds the Following Speci cations:

• Underwriters Laboratories - Hydromassage Bathtubs UL 1795

• ASME A112.19.7M for Whirlpool Appliances

• ANSI Z124.1 for Plastic Bathtubs

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

The EverClean™ system incorporates AlphaSan®, a patented antimicrobial agent manufactured right into the circulation system components, which suppresses the growth of unsightly algae, fungus, mold and mildew.

SEE REVERSE FOR ROUGHING-IN DIMENSIONS AND PRODUCT SPECIFICATIONS

To B e S p e c i  ed - Required:

❏ Color: ❏ Bath Filler: (specify  nish) ❏ Bath Drain: 1583.470 (specify  nish)

To Be Speci ed - Optional:

❏ Safe-T-Heater*: 9075.120 ❏ Jet Trim Ring Kit: 9860.200-two per kit (Specify  nish)

for Body Massage Jets only ❏ Universal Tile Bead Kit: 751755-100

For color/ nish availability and other faucet choices, please see the Product Selector and Pricing Guide.

* NOTE: the Safe-T-Heater is designed to maintain water temperature during operation. It will not heat cold water to desired bathing temperature.

AlphaSan is a registered trademark of Milliken & Co.

Rev. 11/07

GREEN TEA™ 6' x 36"

WHIRLPOOL AND BATHING POOL

HIGH GLOSS

(1829mm)

OUTLINE OF CUTOUT 70.5 x 34.5 (1780 x 876mm)

PUMP

PROVIDE ACCESS TO PUMP FOR SERVICE ON ALL INSTALLATIONS

C/L OF OVERFLOW

(102mm)

ROUGH

FLOOR

INTEGRAL FEET

ON/OFF SWITCH

LEVELING STRINGER NOT FOR SUPPORT

(533mm)

GENERAL SPECIFICATIONS FOR 3573 WHIRLPOOL

INSTALLED SIZE WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW MIN. OPERATING GAL. BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS. CUBE (FT3)

WHIRLPOOL ELECTRICAL SPECIFICATIONS

14-3/4

(375mm)

11-1/2

(292mm)

(914mm)

(229mm)

CUTOUT IN FLOOR FOR DRAIN

(2) AIR VALVES

2 (51mm)

(483mm)

SAFE-T-HEATER REMOVABLE BLANK

72 x 36 x 21 In. (1829 x 914 x 533mm)

19 x 55 In. (483mm x 1397mm)

60-1/2 x 27 In. (1537mm x 686mm)

37 Lbs./Sq. Ft. (175 Kgs/Sq. m.)

115 Lbs. (52 Kg.)

665 Lbs. (302 Kg.)

1.4 HP, 7.5 AMPS, 120V.SYSTEM I PUMP

66 Gal. (250 L.) 49 Gal. (185 L.)

14 In. (356mm)

(1829mm)

OUTLINE OF CUTOUT 70.5 x 34.5 (1780 x 876mm)

C/L OF OVERFLOW

(102mm)

ROUGH

FLOOR

INTEGRAL FEET

LEVELING STRINGER NOT

FOR SUPPORT

(533mm)

(229mm)

CUTOUT IN FLOOR FOR DRAIN

(483mm)

(375mm)

2 (51mm)

14-3/4

(292mm)

11-1/2

(914

GENERAL SPECIFICATIONS FOR 3573 BATHING POOL

72 x 36 x 21 In. (1829 x 914 x 533mm)

19 x 55 In. (483mm x 1397mm)

60-1/2 x 27 In. (1537mm x 686mm)

35 Lbs./Sq. Ft. (170 Kgs/Sq. m.)

78 Lbs. (35 Kg.)

628 Lbs. (285 Kg.)

66 Gal. (250 L.)

14 In. (356mm)

23.8

44.5

23.8

44.5

INSTALLED SIZE WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS. CUBE (FT3)

NOTES:

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISL AND, OR PENINSULA TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGR AL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.

■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.

OPTIONAL 3 WALL TILING BEAD. KIT AND APRON NO. 9260.018 OR 9360.018 AVAILABLE AND MUST BE ORDERED SEPARATELY.

● FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

● IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING

SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.

IMPORTANT: Dimensions of  xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1 These measurements are subject to change or cancellation. No responsibility is assumed for use of super seded or voided lea et.

Rev. 11/07