American Standard 3572, 3574, 3575 User Manual

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The Air
Massage System is completely assembled with air pump, motor, lights, and system piping. All you need to
finish the installation are your selected fittings and electrical connections for an Air Massage System.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

© AS America, Inc. 00
All product names listed herein are trademarks
of AS America, Inc. unless otherwise noted.

FOR AFTER-SALES SERVICE CALL 1 (00) 44-10 WEEKDAYS.

GREEN TEA™ 5' x 36" MODEL 3571

GREEN TEA™ 5-1/2' x 36" MODEL 3572

GREEN TEA™ 6' x 36" MODEL 3573

GREEN TEA™ 5' x 42" MODEL 3574

GREEN TEA™ 6' x 42" MODEL 3575

TOWN SQUARE

®

5' x 42" MODEL 2748

TOWN SQUARE

®

6' x 42" MODEL 2742

ELLISSE OVAL MODEL 2709

INSTALLATION GUIDE FOR

AIR MASSAGE SYSTEM

1

754063-100 Rev. B

TABLE OF CONTENTS:

Cover

................................................................................................Page 1

Table of Contents

..............................................................................Page 

Safety Instructions Notice.................................................................Page 3

Roughing-in Reference.....................................................................Page 4 - 6

Installation and Framing Instructions................................................Page 7 - 

Supplied Drain Assembly and Installation Instructions.....................Page  - 13

Post Installation Instructions.............................................................Page 14

Remote Blower Location Option.......................................................Page 15

Warranty

...........................................................................................Page 16

754063-100 Rev. B



IMPORTANT SAFETY

INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS!

!

!

!

!

!

!

WARNING: Risk of personal injury. Do not permit children to use this bathtub without adult supervision.

WARNING: Risk of electric shock. Do not permit electrical appliances near any bathtub when bathtub contains water.

WARNING:

Risk of hyperthermia and possible drowning.

People using medications and/or having adverse medical

history should consult a physician before using this product.

WARNING: Risk of personal injury. Do not overfill bathtub before entering. Entering tub when filled more than /3 can

cause overflow and slippery conditions. Exercise caution when entering and exiting.

WARNING:

No Food or Alcoholic Beverages.

Use of your bathtub immediately after meals is not recommended. Avoid
alcohol consumption before or during bathing. Alcoholic beverages can cause drowsiness or hyperthermia resulting in loss of
consciousness or even drowning.

WARNING:

Pregnancy.

If you are or think you may be pregnant, consult your physician before using the bathtub.

Use this unit only for its intended use as described in this manual. Do not use any attachments not recommended by American
Standard.

The unit must be connected only to a supply circuit that is properly protected by a ground-fault circuit-interrupter (GFCI). Such a
GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the test button. The
GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the
GFCI is defective. If the GFCI interrupts power to the bathtub without the test button being pushed, a ground current is flowing,
indicating the possibility of an electric shock. Do not use this air bath. Disconnect the air bath and have the problem corrected by a
licensed electrician before using.

SAVE THESE INSTRUCTIONS

3

754063-100 Rev. B

ELLISSE OVAL

MODEL 2709 AIR BATH

C/L

FOR SPOUT

& VALVES

FOR HAND
SPRAY

FITTINGS
DECK

EDGE OF
FITTINGS

DECK

35-3/4

(908mm)

TO END OF TUB

1-1/2

(38mm)

1-1/2

(38mm)

1-1/2

(38mm)

2-1/2

(64mm)

4-1/2

(114mm)

4-1/2

(114mm)5(127mm)

DRAIN

ROUGHING-IN REFERENCES

HOLE DRILLING LOCATION FOR AMERICAN STANDARD "TOWN SQUARE"

DECK MOUNT BATH FILLER WITH PERSONAL SHOWER, MODEL #2555.901 ONLY

C/L

FOR SPOUT

& VALVES

FOR HAND

SPRAY

FITTINGS
DECK

EDGE OF
FITTINGS

DECK

29-3/4

(755mm)

TO END OF TUB

1-1/2

(38mm)

1-1/2

(38mm)

1-1/2

(38mm)

2-1/2

(64mm)

4-1/2

(114mm)

4-1/2

(114mm)5(127mm)

DRAIN

HOLE DRILLING LOCATION FOR AMERICAN STANDARD "TOWN SQUARE"

DECK MOUNT BATH FILLER WITH PERSONAL SHOWER, MODEL #2555.901 ONLY

TOP VIEW

TOWN SQUARE® 5' x 42"

MODEL 2748 AIR BATH

59-1/2"

(1511mm)

INTEGRAL
FITTING DECK
2-1/2" X 14"
(64 X 356mm)

29-3/4"

(755mm)

41-5/8"

(1057mm)

CONTROL
PANEL

OUTLINE OF CUTOUT

58" X 40-1/8"

(1473 X 1019mm)

PROVIDE ACCESS TO BLOWER FOR

SERVICE ON ALL INSTALLATIONS

C/L OF
DRAIN
OUTLET

FLOOR CUTOUT

9" X 18"

(229 X 458mm)

3/4"
(19mm)

14-1/2"

(368mm)

5-1/4"
(133mm)

3"

(76mm)

OUTLINE OF SKID

RESISTANT SURFACE

20 AIR JETS

EDGE OF
FLOOR
CUTOUT

AIR

BLOWER

LEVELING STRINGER

(NOT FOR SUPPORT)

1-1/2" N.P.T. THREADS

2"

(51mm)

5-3/4"

(146mm)

C/L OF
OVERFLOW

21"

(533mm)

23"

(584mm)

ROUGH

FLOOR

INTEGRAL FEET WITH

ATTACHED BASEBOARD

1-1/2" O.D. TAILPIECE

3/4"
(19mm)

3-1/8"

(79mm)

AIR

BLOWER

7-3/4" TYPICAL
(197mm)

10-1/4"

(260mm)

END VIEW

END VIEW

TOP VIEW

CONTROL
PANEL

41-3/4"

(1060mm)

26-3/4

(679mm)

7-3/4” TYPICAL
(197mm)

OUTLINE OF SKID
RESISTANT SURFACE

35-3/4"

(908mm)

13-1/4"

(337mm)

4"

(102mm)

71-1/2"

(1816mm)

3"

(76mm)

FLOOR CUTOUT
9" X 19"
(229 X 459mm)

OUTLINE OF CUTOUT
70" X 40-1/4" (1778 X 1022mm)

PROVIDE ACCESS
TO BLOWER FOR
SERVICE ON ALL
INSTALLATIONS

INTEGRAL
FITTING DECK
2-1/4" X 14"
(57 X 356mm)

3/4"

(19mm)

EDGE OF
FLOOR
CUTOUT

AIR BLOWER

C/L OF
DRAIN
OUTLET

20 AIR JETS

LEVELING STRINGER
(NOT FOR SUPPORT)

1-1/2" N.P.T. THREADS

2"

(51mm)

3-1/4"

(83mm)

C/L OF
OVERFLOW

20"

(508mm)

22"

(559mm)

ROUGH

FLOOR

1-1/2" O.D.TAILPIECE

5/8"

(16mm)

3"
(76mm)

AIR BLOWER

10-1/4”

(260mm)

INTEGRAL FEET WITH
ATTACHED BASEBOARD

TOP VIEW

END VIEW

TOP VIEW

END VIEW

FLOOR CUTOUT
229 X 459mm
(9" X 19")

1759 mm

(69-1/4")

OUTLINE OF
CUTOUT

240 mm

(9-7/16")

978 mm
(38-1/2")

489mm

(19-1/4")

76mm

(3")

C

L

OF DRAIN
OUTLET

PROVIDE ACCESS

TO BLOWER FOR

SERVICING ON ALL

INSTALLATIONS

16 AIR JETS

AIR

BLOWER

SEE FTTG.SPECS

FOR DIMENSION

C

L

OF SUPPLIES

CONTROL

PANEL

11-1/4"

(286mm)

7-3/4" TYPICAL
(197mm)

ROUGH
FLOOR

1-1/2" O.D. TAILPIECE

495mm

(19-1/2")

INTEGRAL FEET

WITH ATTACHED

BASEBOARD

86mm (3-3/8")

38mm

(1-1/2")

533mm

(21")

1-1/2" N.P.T.M. THREADS

35mm

(1-3/8")

98mm
(3-7/8")

C

L

TO OVERFLOW

TOWN SQUARE® 6' x 42"

MODEL 2742 AIR BATH

GREEN TEA™ 5' x 36"

MODEL 3571 AIR BATH

LEVELING STRINGER NOT
FOR SUPPORT

60

(1524mm)

36

(914mm)

11-1/2

(292mm)

OUTLINE OF CUTOUT 58.5 x 34.5 (1486 x 876mm)

14-3/4

(375mm)

CONTROL
PANEL

BLOWER

CUTOUT IN FLOOR FOR DRAIN

20 AIR JETS

9

(229mm)

C

L

PROVIDE ACCESS TO BLOWER FOR
SERVICE ON ALL INSTALLATIONS

ROUGH
FLOOR

1-1/2" O.D. TAILPIECE

508mm

(20")

INTEGRAL FEET
WITH ATTACHED
BASEBOARD

51mm

(2")

559mm

(22")

1-1/2" N.P.T.M. THREADS

35mm

(1-3/8")

98mm
(3-7/8")

C

L

TO OVERFLOW

102mm (4")

754063-100 Rev. B

4

GREEN TEA™ 6' x 36"

MODEL 3573 AIR BATH

GREEN TEA™ 5' x 42"

MODEL 3574 AIR BATH

ROUGHING-IN REFERENCES

TOP VIEW

END VIEW

TOP VIEW

END VIEW

TOP VIEW

END VIEW

TOP VIEW

END VIEW

GREEN TEA™ 5-1/2' x 36"

MODEL 3572 AIR BATH

GREEN TEA™ 6' x 42"

MODEL 3575 AIR BATH

22 AIR JETS

PROVIDE ACCESS TO BLOWER FOR
SERVICE ON ALL INSTALLATIONS

66

(1676mm)

36

(914mm)

11-1/2

(292mm)

14-3/4

(292mm)

BLOWER

C

L

CUTOUT IN FLOOR FOR DRAIN

9

(229mm)

OUTLINE OF CUTOUT 64.5 x 34.5 (1638 x 876mm)

CONTROL
PANEL

LEVELING STRINGER NOT
FOR SUPPORT

ROUGH
FLOOR

1-1/2" O.D. TAILPIECE

508mm

(20")

INTEGRAL FEET
WITH ATTACHED
BASEBOARD

51mm

(2")

559mm

(22")

1-1/2" N.P.T.M. THREADS

35mm

(1-3/8")

98mm
(3-7/8")

C

L

TO OVERFLOW

102mm (4")

72

(1829mm)

36

(914mm)

11-1/2

(292mm)

OUTLINE OF CUTOUT 70.5 x 34.5 (1780 x 876mm)

14-3/4

(375mm)

CONTROL
PANEL

BLOWER

CUTOUT IN FLOOR
FOR DRAIN

C

L

9

(229mm)

LEVELING STRINGER NOT
FOR SUPPORT

ROUGH
FLOOR

1-1/2" O.D. TAILPIECE

508mm

(20")

INTEGRAL FEET
WITH ATTACHED
BASEBOARD

51mm

(2")

559mm

(22")

1-1/2" N.P.T.M. THREADS

35mm

(1-3/8")

98mm
(3-7/8")

C

L

TO OVERFLOW

102mm (4")

PROVIDE ACCESS TO BLOWER FOR
SERVICE ON ALL INSTALLATIONS

23 AIR JETS

60

(1524mm)

42

(1067mm)

11-1/2

(292mm)

OUTLINE OF CUTOUT 58.5 x 40.5 (1486 x 1029mm)

14-3/4

(375mm)

BLOWER

C

L

9

(229mm)

CUTOUT IN FLOOR FOR DRAIN

CONTROL
PANEL

LEVELING STRINGER NOT
FOR SUPPORT

ROUGH
FLOOR

1-1/2" O.D. TAILPIECE

508mm

(20")

INTEGRAL FEET
WITH ATTACHED
BASEBOARD

51mm

(2")

559mm

(22")

1-1/2" N.P.T.M. THREADS

35mm
(1-3/8")

98mm
(3-7/8")

C

L

TO OVERFLOW

102mm (4")

PROVIDE ACCESS TO BLOWER FOR
SERVICE ON ALL INSTALLATIONS

23 AIR JETS

72

(1829mm)

42

(1067mm)

11-1/2

(292mm)

OUTLINE OF CUTOUT 70.5 x 40.5 (1780 x 1029mm)

14-3/4

(375mm)

BLOWER

C

L

9

(229mm)

CUTOUT IN FLOOR FOR DRAIN

CONTROL
PANEL

PROVIDE ACCESS TO BLOWER FOR
SERVICE ON ALL INSTALLATIONS

LEVELING STRINGER NOT
FOR SUPPORT

ROUGH
FLOOR

1-1/2" O.D. TAILPIECE

508mm

(20")

INTEGRAL FEET
WITH ATTACHED
BASEBOARD

51mm

(2")

559mm

(22")

1-1/2" N.P.T.M. THREADS

35mm

(1-3/8")

98mm
(3-7/8")

C

L

TO OVERFLOW

102mm (4")

27 AIR JETS

5

754063-100 Rev. B

ROUGHING-IN REFERENCES

GENERAL SPECIFIC ATIONS F OR 2748

AIR MAS SAGE SYST EM

59- 1/2 x 41-5 /8 x 23 In. (1 511 x 10 57 x 5 84mm)

110 Lbs. (50 Kg. )

611 Lbs. (278 Kg .)

60 Gal. (227 L)

34 x 24 In. ( 864 x 61 0mm )

52 x 31 In. ( 132 1 x 1 321 mm)

12- 1/2 I n. (3 18m m)

40 Lbs./ Sq.Ft . ( 194 K gs. /Sq .m)

27. 8

45. 4

1.0 HP, 10 AM PS ,120V .BLO WER

ELECTRI CAL SPECI FICATION S

INS TALLE D SIZ E
WEI GHT
WEI GHT w /WATE R
GAL . TO OVERF LOW
BAT HING WELL AT SUMP
BAT HING WELL AT RIM
WAT ER DE PTH T O O VERFL OW
FLO OR LO ADING
(PR OJECT ED AR EA)
PTS .

CUB E (FT3)

GENERAL SPECIFI CATIONS F OR 2709 AIR BATH

69- 1/4 x 38-1 /2 x 19- 3/4 In .(175 9 x 97 8 x 5 02m m)

107 Lbs. (49 Kg. )

640 Lbs. (291 Kg .)

64 Gal. (243 L)
45 x 23 In. ( 114 3 x 5 84m m)
63 x 32 In. ( 160 0 x 8 13m m)

13 In. ( 330mm )

35 Lbs./ Sq.Ft . ( 166 K gs. /Sq .m)

25. 6

49. 4

ELECTRICAL SPECIFICATIONS

1.0 HP, 10 AMPS , 120V.BLO WER

INS TALLE D SIZ E
WEI GHT
WEI GHT w /WATE R
GAL . TO OVERF LOW
BAT HING WELL AT SUMP
BAT HING WELL AT RIM
WAT ER DE PTH T O O VERFL OW
FLO OR LO ADING
(PR OJECT ED AR EA)
PTS .
CUB E (FT3)

GENERAL SPECIFICA TIONS FOR 2742

AIR MASS AGE SYSTE M

71- 1/2 x 41-3 /4 x 22 I n. (1 816 x 1060 x 55 9mm)

115 Lbs. (52 Kg.)

690 Lbs. (313 Kg.)

69 Gal. (261 L)
41 x 21- 1/2 I n. (1 041 x 546 mm)
62 x 31- 1/2 I n. (1 574 x 800 mm)

14- 1/4 I n. (3 62mm)

33 Lbs. /Sq.F t. (1 63 K gs./S q.m)

27. 8

55. 7

1.0 HP, 10 AM PS ,1 20V .BLO WER

ELECTRIC AL SPECIF ICATIONS

INS TALLE D SIZ E
WEI GHT
WEI GHT w /WATE R
GAL . TO OVERF LOW
BAT HING WELL AT SU MP
BAT HING WELL AT RI M
WAT ER DE PTH T O OVE RFLO W
FLO OR LO ADING
(PR OJECT ED AR EA)
PTS .

CUB E (FT3)

6 0 x 3 6 x 2 2 In. (15 24 x 914 x 559m m)

86 Lbs. (39 K g.)

519 Lbs. (235 Kg.)

52 Gal. (197 L.)
38 Gal. (144 L.)

19 x 43 In. ( 483mm x 1 092mm )

48- 1/2 x 27 I n. (1 232m m x 6 86mm)

14 In. ( 356mm )

35 Lbs./ Sq. F t. (1 69 K gs/Sq . m.)

23. 8

44. 5

GENERAL SPECIFIC ATIONS FO R 3571

AIR BATH SYSTEM

INS TALLE D SIZ E
WEI GHT
WEI GHT w /WATE R
GAL . TO OVERF LOW
MIN . OPE RATIN G GAL .
BAT HING WELL AT SU MP
BAT HING WELL AT RI M
WAT ER DE PTH T O OVE RFLO W
FLO OR LO ADING
(PR OJECT ED AR EA)
PTS .
CUB E (FT3)

ELECTRIC AL SPECI FICATIONS

1.0 HP, 10 AM PS, 1 20V.BLOWER

6 6 x 3 6 x 2 2 I n. (1676 x 914 x 55 9mm )

100 Lbs. (45 Kg. )

592 Lbs. (269 Kg .)

59 Gal. (223 L.)
44 Gal. (167 L.)

19 x 49 In. ( 483 mm x 124 5mm )

54- 1/2 x 27 I n. (1384 mm x 6 86m m)

14 In. ( 356mm )

36 Lbs./ Sq. F t. (175 Kgs /Sq . m .)

25. 6

45. 1

GENERAL SPECIFI CATIONS F OR 3572

AIR BATH SYSTEM

INS TALLE D SIZ E

WEI GHT
WEI GHT w /WATE R
GAL . TO OVERF LOW
MIN . OPE RATIN G G AL.
BAT HING WELL AT SUMP
BAT HING WELL AT RIM
WAT ER DE PTH T O O VERFL OW
FLO OR LO ADING
(PR OJECT ED AR EA)
PTS .
CUB E (FT3)

ELECTRI CAL SPEC IFICATIO NS

1.0 HP, 10 AM PS, 120V .BLOWER

7 2 x 3 6 x 2 2 In. (18 29 x 914 x 559m m)

115 Lbs. (52 Kg.)

665 Lbs. (302 Kg.)

66 Gal. (250 L.)
49 Gal. (185 L.)

19 x 55 In. ( 483mm x 1 397mm )

60- 1/2 x 27 I n. (1 537m m x 6 86mm)

14 In. ( 356mm )

37 Lbs./ Sq. F t. (1 75 K gs/Sq . m.)

23. 8

44. 5

GENERAL SPECIFIC ATIONS FO R 3573

AIR BATH SYSTEM

INS TALLE D SIZ E
WEI GHT
WEI GHT w /WATE R
GAL . TO OVERF LOW
MIN . OPE RATIN G GAL .
BAT HING WELL AT SU MP
BAT HING WELL AT RI M
WAT ER DE PTH T O OVE RFLO W
FLO OR LO ADING
(PR OJECT ED AR EA)
PTS .
CUB E (FT3)

ELECTRI CAL SPECI FICATIONS

1.0 HP, 10 AM PS, 1 20V.BLOWER

5 9-3/4 x 42 x 22 In . ( 151 8 x 10 60 x 559 mm)

115 Lbs. (52 Kg. )

656 Lbs. (298 Kg .)

65 Gal. (246 L.)
47 Gal. (178 L.)

24- 1/2 x 42 I n. (622m m x 10 67m m)

48 x 33 In. ( 121 9mm x 83 8mm )

14 In. ( 356mm )

38 Lbs./ Sq. F t. (185 Kgs /Sq . m .)

27. 8

47. 4

GENERAL SPECIFI CATIONS F OR 3574

AIR BATH SYSTEM

INS TALLE D SIZ E
WEI GHT
WEI GHT w /WATE R
GAL . TO OVERF LOW
MIN . OPE RATIN G G AL.
BAT HING WELL AT SUMP
BAT HING WELL AT RIM
WAT ER DE PTH T O O VERFL OW
FLO OR LO ADING
(PR OJECT ED AR EA)
PTS .
CUB E (FT3)

ELECTRI CAL SPEC IFICATION S

1.0 HP, 10 AM PS, 120V .BLOWER

7 2 x 4 2 x 2 2 In. (18 29 x 1067 x 559 mm)

127 Lbs. (58 Kg.)

785 Lbs. (356 Kg.)

79 Gal. (299 L.)
58 Gal. (219 L.)

22- 1/2 x 54 I n. (5 72mm x 13 72mm)

60 x 33 In. ( 1524m m x 838mm )

14 In. ( 356mm )

37 Lbs./ Sq. F t. (1 85 K gs/Sq . m.)

25. 6

49. 4

GENERAL SPECIFIC ATIONS F OR 3575

AIR BATH SYSTEM

INS TALLE D SIZ E
WEI GHT
WEI GHT w /WATE R
GAL . TO OVERF LOW
MIN . OPE RATIN G GAL .
BAT HING WELL AT SU MP
BAT HING WELL AT RI M
WAT ER DE PTH T O OVE RFLO W
FLO OR LO ADING
(PR OJECT ED AR EA)
PTS .
CUB E (FT3)

ELECTRI CAL SPECI FICATIONS

1.0 HP, 10 AM PS, 1 20V.BLOWER

ELLISSE OVAL

MODEL 2709 AIR BATH

TOWN SQUARE® 5' x 42"

MODEL 2748 AIR BATH

TOWN SQUARE® 6' x 42"

MODEL 2742 AIR BATH

GREEN TEA™ 5' x 36"

MODEL 3571 AIR BATH

GREEN TEA™ 6' x 36"

MODEL 3573 AIR BATH

GREEN TEA™ 5' x 42"

MODEL 3574 AIR BATH

GREEN TEA™ 5-1/2' x 36"

MODEL 3572 AIR BATH

GREEN TEA™ 6' x 42"
MODEL 3575 AIR BATH

754063-100 Rev. B

6

60-1/4"

35"
36"

1"
5-1/"
34-1/"

1530mm

mm
14mm
43mm

146mm

76mm

66-1/4"

35"
36"

1"
64-1/"
34-1/"

163mm

mm
14mm
43mm

163mm

76mm

7-1/4"

35"
36"

1"
70-1/"
34-1/"

135mm

mm
14mm
43mm

171mm

76mm

60"
40-3/4"
41-3/4"

1"
5-1/4"
40-1/4"

154mm
1035mm
1060mm

43mm
140mm
10mm

7-1/4"

41"
4"

1"
70-1/"
40-1/"

135mm
1041mm
1067mm

43mm
171mm
10mm

INSTALLATION AND FRAMING INSTRUCTIONS:

The variety of installations possible for this air massage system may require framing procedures
other than those shown. Locate studs as required. Ensure roughing-in dimensions are proper,
plumb and square. Provisions must be made in all installations for an access opening for servicing
the air blower and controls. It is strongly recommended that an additional opening be provided for
access to the drain components. The apron should not be used as the primary access opening.

1. Position the air massage system into the installation opening and level the deck in both
directions, shimming the integral feet with attached baseboard as necessary. Refer to the Air
Bath Installation Table for nominal installation dimensions. Mark the final position of the
underside of the deck by tracing a line on to the studs (see Figure 1).

. Remove the air massage system and attach a 1 x 4 stringer to the studs, with the top of the

stringer touching the traced line.

The rim of the bath must not support weight.

TYPICAL PIER TYPE INSTALLATION

AS DESIRED

F

CUTOUT

AS DESIRED

E

CUTOUT

D

4

(610 mm)

1

(305 mm)

MOUNTING
SURFACE

WATERPROOF
SEALANT

BATH

TYPICAL RECESS INSTALLATION

4

(610 mm)

1

(305 mm)

D

A

B

C

LEVELING
STRINGERS

TILE

TILE
BEAD
STRIP

LEVELING STRINGER

1 x 4 (not for support)

BATH

ADHESIVE

SEALANT

WALLBOARD

NOTE: Tile bead kit not included
and must be purchased separately.

D

TYPICAL
INSTALLATION

FIGURE 1

3. Install supplied cable drain components to the air massage system according to the enclosed drain installation
instructions. Before replacing your air bath for final installation, be certain that an opening has been provided in
the sub-floor for the drain. See the roughing-in drawing for suggested opening size (shadowed) and location
dimensions. The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout
in the floor.

4. Replace air massage system and re-shim the integral support feet with attached baseboard, shimming the entire
length of the baseboard as needed. Secure the shims using construction adhesive, silicone or equivalent
materials.

The rim of the bath must not support weight. Any finish material such as tile or wall board must be

self-supporting if it contacts the deck of the bath.

!

!

ACCESS PANEL MUST BE LOCATED
ON THE SAME SIDE AS THE MOTOR.

ALLOW OPEN FRAMING ON PUMP/MOTOR
END FOR SERVICE.

ACCESS PANEL MUST BE LOCATED
ON THE SAME SIDE AS THE BLOWER.

ALLOW OPEN FRAMING ON
BLOWER END FOR SERVICE.

UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)

IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.

UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)

IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.

NOTE:

FRONT EDGE
OF BATH MUST
BE SUPPORTED
BY STUD WALL OR
AMERICAN STANDARD
APRON KIT

** USE CUTOUT TEMPLATE PROVIDED FOR 70 MODEL

NOTICE:

DO NOT BUILD THE SURROUNDING STRUCTURE BEFORE RECEIVING YOUR AIR BATH.
STRUCTURE MEASUREMENTS SHOULD BE VERIFIED AGAINST THE ACTUAL AIR BATH
RECEIVED TO ENSURE PROPER FIT.

AIR BATH INSTALLATION TABLE

DIM.

DESCRIPTION

A
B
C
D
E
F

5-3/4"
3-3/4"
41-3/4"

1"
5"

40-1/"

151mm
1511mm
1060mm

533mm
1473mm
101mm

Nominal tub length recess opening
Nominal tub apron support opening
Nominal tub width recess opening
Nominal tub height opening
Nominal tub length cutout
Nominal tub width cutout

71-3/4"
3-3/4"
41-3/4"

0"
70"

40-1/4"

13mm
1511mm
1060mm

50mm
177mm
10mm

1-1/"

67"

36-1/"

45mm

170mm

7mm

**

2748 2742

AIR BATH MODEL NUMBER

2709

3571 3572 3573 3574 3575

7

754063-100 Rev. B

All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes.

WARNING: When using electrical products, basic precautions should always be observed, including the following:

1. DANGER: RISK OF ELECTRIC SHOCK! Connect only to a circuit protected by a ground-fault circuit interrupter.

2. Permit access for servicing blower as noted.

3. All building materials and wiring should be routed away from the air blower.

AIR MASSAGE SYSTEM

ELECTRICAL INSTALLATION INSTRUCTIONS

ELECTRICAL DIAGRAM

READ AND FOLLOW ALL INSTRUCTIONS

WIR E SE L ECT I ON G UID E

Max i mum dis t anc e fr o m

fus e box to m oto r

The siz e s s h own on t his

cha r t a r e r e com m end a tio n s

for cop p er c ond u cto r s

onl y . A lwa y s f o llo w

loc a l a n d n a tio n al

ele c tri c al c ode s

Mot o r

Hi P erf o rma n ce

Rat i ng

2.1 H.P . ,

1.4 H.P . ,

and 1.2 5 H. P .

50' 1 0 0'

115 V Po w er L ine

150 ' 200 '

12 10 8 8

AIR MASSAGE SYSTEM:

The air bath should be installed on a 10 vac, 15 or 0 amp dedicated circuit. The circuit should be hard-wired
from the electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel.
A grounded neutral wire and a third wire, earth ground, are essential.

!

USE 15 OR 20 AMP

GFCI OUTLET

AIR BLOWER

CHROMATHERAPY LIGHT

CONTROL BOX (OPTIONAL)

BL AC K

WH IT E

120 VAC

GND .

754063-100 Rev. B



Please note that care must be taken to protect the surface of the tub during all aspects of the installation.
Do not drill or cut the bath deck with the tub directly beneath it as damage to the tub may result.

1. Install the tub per the installation instructions provided with the unit.
. Prepare the bath deck support structure per the local codes. Note - the bath deck must be self supporting.

3. Cut bath deck to your specifications.

4. Place the bath deck in position and trace the opening on the tub with a soft pencil. Do not drill or cut the bath
deck with the tub directly beneath it as damage to the tub may result.

5. Remove the bath deck and apply a generous bead of waterproof sealant on the outer edge of the traced line.

6. Replace the bath deck and secure it into place.

7. Apply additional sealant along the tub and bath deck interface as necessary to ensure a watertight seal.

. Remove excess sealant per the manufacturer's instructions.

Finished bath deck surface material must be

self-supporting and secured per local codes

Tub support structure per installation
instructions provided with the tub

Bath deck support material

Bathtub

Waterproof

Sealant

UNDER DECK MOUNTING INSTRUCTIONS

DRAIN STOPPER

WITH

ADJUSTABLE

BOLT

METAL STRAINER

BOLT

METAL

STRAINER

FLAT RUBBER

GASKET

DRAIN WASTE

FLANGE

OVERFLOW

ASSEMBLY

OVERFLOW NUT WITH O-RING

OVERFLOW

ESCUTCHEON

PLASTIC DRAIN BASE

DRAIN ACTUATOR SHAFT

SET

SCREW

AIR BATH NUT

WITH WASHER

AND GASKET

OVERFLOW

RETAINER

WEDGE

GASKET

CLOSE

OPEN

OVERFLOW

ASSEMBLY

VERTICAL

DRAIN PIPE

HORIZONTAL

DRAIN PIPE

PLASTIC

DRAIN BASE

0˚ ELBOW

AIR BATH DRAIN ILLUSTRATION

With supplied cable drain assembled to
bath, connect drain outlet to waste line in
accordance with the drain assembly
instructions. Tighten all drain joints
securely. Check the couplings and make
sure they are hand-tight. Clean the air
bath and fill with water to a point " below
the overflow. Recheck the couplings and
make certain that they are not leaking.
(Although the couplings are factory
tightened and inspected, some loosening
may have occurred during transit.) Make
sure the air bath is connected to the
electrical supply and turn the air bath on.
Check for leaks around all piping
connections while the air bath is running.

DRAIN CONNECTION AND

SYSTEM TEST

(before installing bath into

framed out structure)



754063-100 Rev. B

DRAIN CONNECTION

1. Remove and identify all drain components as defined in air bath drain illustration.

2. Find 1" schedule 40 PVC pipe, see pipe chart, HORIZONTAL DRAIN PIPE.
Mark as "horizontal pipe", drain to elbow section.

3. Find 1" schedule 40 PVC pipe, see pipe chart, VERTICAL DRAIN PIPE.
Mark as "vertical pipe", drain to elbow section.

4. Install drain from below unit through opening as shown in photo A.

5. Apply 3 or 4 pea sized dabs of 100% silicone sealant to bottom waste drain flange and press flat rubber gasket into place
as shown in photos B and C.

6. Apply 1/" continuous bead of 100% silicone sealant to flat rubber gasket as shown in photo D. Set aside and be sure not to
disturb silicone bead.

7. Apply 1/" continuous bead of 100% silicone sealant to back side to metal strainer as shown in photo E. Press
Strainer retaining bolt into metal strainer and insert into drain hole of acrylic bath.

A.

B.

C.

D.

E.

HORIZONTAL

PIPE

VERTICAL

PIPE

MODEL

74

74

70

3571

357

3573

3574

3575

10.50"

1.00"

11.00"

1.75"

1.50"

1.75"

1.5"

1.50"

6.50"

6.50"

4.75"

5.75"

6.00"

5.75"

5.75"

5.75"

PIPE CHART

754063-100 Rev. B

10

DRAIN CONNECTION continued...

8. Have assistant take drain assembly from step 6 and place over back surface of drain hole to engage the metal strainer bolt.

Secure plastic drain base to metal strainer in drain opening using nut driver shaft. DO NOT OVER TIGHTEN! Carefully
remove excess silicone from acrylic surface as directed by silicone sealant directions.

9. From unit back side, overflow nut should be in alignment with overflow opening, as shown in photo F.

10. Slide air bath fitting nut, washer and gasket onto air bath fitting as shown in photos G and H.

11. Assemble air bath fitting to plastic drain base as shown in photos I, J, K and L. Hand tighten nut to create watertight joint.

F.

G.

H.

I.

J.

K.

L.

Overflow nut

O-ring

Air bath

fitting

11

754063-100 Rev. B

DRAIN CONNECTION continued...

12. Apply PVC cement to Horizontal Drain Pipe PVC and assemble to 0 degree elbow.

13. Dry fit Vertical Drain Pipe PVC into overflow assembly, then insert into elbow, WITHOUT PVC GLUE to align drain and
overflow to bath. Mark overflow female coupling as shown in photo M.

14. Test fit and trim pipe as required to get overflow drain into center of overflow hole BEFORE GLUING vertical pipe into
0 degree elbow, as shown in photos N-1 and N-2.

15. Apply PVC cement to Vertical Drain Pipe sub-assembly and assemble per re-aligned marks from step 13.

16. Disassemble overflow wedge gasket and chrome overflow retainer as shown in photo O.

17. Place overflow wedge gasket onto plastic overflow pipe flange with round raised rib surface contacting flange
as shown in photo P.

O.

M.

P.

N-1. N-2.

754063-100 Rev. B

1

DRAIN CONNECTION

continued...

18. Tighten chrome overflow retainer onto drain overflow assembly pipe per photo Q below.

19. Align flat on drain actuator shaft with corresponding flat in chrome metal overflow escutcheon and tighten set screw to fix
overflow escutcheon in place per photos R and S.

20. Rotate left and right lightly to feel stops in drain cable control. This opens and closes drain.

21. Place drain stopper into drain waste hole as shown in photo T.

22. The drain stopper should prevent water from draining out of tub when the escutcheon is in the fully counterclockwise

position as shown in photo U. Adjust the drainstopper bolt to obtain the best water seal in the tub.

23. Rotate Drain Escutcheon to clockwise stop. This should open drain, between 1/" and 1/4", to allow water to exit bath.
If not adjust metal bolt in drain stopper to allow draining function, but not so high that drain will not seal when closed to
hold water during use. See photo V.

Q.

R.

U.

S.

V.

T.

13

754063-100 Rev. B

POST INSTALLATION CLEAN-UP

Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.
Do not use wire brushes or any other metal implement on bath surface.

Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent.
Stubborn dirt or stains may be removed using granular Spic and Span® mixed with water.

Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.

AFTERCARE and CLEANING

• The high gloss surface is resistant to impact and chemicals and will retain its lasting luster with proper care and maintenance.

• Always fill the tub with temperate water. Excessively hot water may cause surface damage

• Clean after use with a mild liquid household detergent cleaner. Do not use Lestoil, Lysol Disinfectant (spray or concentrate),
or Lysol Basin, Tub and Tile Cleaner, Windex, Mr. Clean, Dow Disinfectant Bathroom Cleaner, or cleaning products in
aerosol cans.

HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.

• Do not use wire brushes, knives or sharp objects to remove stains, cigarette tar deposits,or other surface blemishes.

• Abrasive cleaners or powders must not be used, since they will dull the surface. If the glossy surface looses its sheen, dulled
areas can be restored by rubbing with a white "automotive type" polishing compound and waxing with a "liquid wax."

• Do not wax areas where you walk or stand.

• Do not allow nail polish remover, acetone, dry cleaning fluid, paint remover or other solvents to come into contact with
the surface.

• Clean the surrounding surface immediately after using caustic drain cleaners.

• Burning cigarettes will damage the surface.

• Should damage to the fixture occur, repairs can be made quickly and easily.
Your distributor or builder can provide details.

• Do not permit drain cleaner to enter the circulation system.

754063-100 Rev. B

14

REMOTE BLOWER LOCATION OPTION

IMPORTANT! It is not necessary that the blower motor be relocated. This option is provided for the case that a particular

installation makes this effort practical.

NOTE:

Relocating blower motor from factory installed location, see photo W, will require disassembly of air blower from mounting
board. Keep all hardware for reattachment at new location. Additional hardware will be required depending upon final desired
position of air blower. Follow all instructions listed below.

NOTE: Installing the blower in a remote location will reduce the system efficiency.

NOTE: Relocating a blower motor still requires a service access for the blower.

NOTE:

All materials needed for the relocation must be supplied by the installer. This includes ordering a longer control panel cable
(P/N 75405-0071A).

A separate circuit, which must be protected by the Ground Fault Circuit Interrupter (GFCI), is required in the remote location.
Electrical connections should be performed by a licensed electrician.

Choose a space as close to the bath as possible so the system works as efficiently as possible. The space must be at least 30 cubic
feet and the blower must be mounted at least  inches above the floor and  inches minimum away from any wall. The blower must
NOT be installed in an attic area.

The blower motor must be located within 1 feet of rigid piping from the bath air manifold. This limitation is for the total pipe length
and applies to any direction changes and elbows. There can be no more than six changes of direction. There should be as few
direction changes as possible and the piping installation must meet all requirements of local plumbing and building codes.

Disconnect the blower from the flexible hose as shown in photo X. Do NOT remove the check valve manifold that is mounted to the
underside of the air bath. The manifold MUST remain mounted above the tub overflow level as shown in X.

Use 1 1/” PVC rigid piping and couplings to extend the blower motor location as shown in photos Y and Z. Detach the flexible hose
section from the blower end and extend the air line by adding the appropriate length of PVC piping. Mount the blower in a horizontal
direction using the mounting screws provided with the air bath system. Do NOT glue piping to either the manifold or blower. These
couplings MUST be attached to the piping with screws as shown in photos Y and Z. Glue only the PVC piping and couplings needed
to extend the air line. Let the glued couplings set overnight before attaching the blower and manifold couplings with screws.

CAUTION: It is imperative to let the glued piping set overnight as there may be fumes from the glue that could be ignited if not
allowed to dissipate.

W.

X.

Y. Z.

TYPICAL VIEW

TYPICAL VIEW

Do NOT move check
valve manifold

15

754063-100 Rev. B

By Mail: American Standard Inc.
P.O. Box 65
West Caldwell, N.J. 07007
Attention: Customer Care Center

AS America, Inc. Limited Lifetime Warranty for Premium Acrylic Air Baths

AS America, Inc. (”American Standard”) warrants to the original consumer purchaser that it will, at its option,
repair or replace this whirlpool or any of its parts that are found by American Standard, in its sole judgment,
to be defective under normal residential use and maintenance so long as it is owned by the original
consumer purchaser.

This warranty shall only become effective upon receipt by American Standard of a completely filled out
Warranty Registration Card evidencing proof of purchase.

This limited warranty does not apply to commercial installations. The warranty for commercial installations is
three (3) years.

THIS WARRANTY SHALL BE VOID IF THE ACCESS PANEL TO THE WHIRLPOOL IS COVERED IN ANY
MANNER CONTRARY TO THE INSTALLATION INSTRUCTIONS. In no event will American Standard be
liable for the cost of repair or replacement of any installation materials including but not limited to tiles,
marble etc.

This limited warranty DOES NOT COVER the following:

1. Defects or damages arising from shipping, installation, alterations, accidents, abuse, misuse, lack of
proper maintenance and cleaning as directed in the owner’s manual and use of other than genuine
American Standard replacement parts, in all cases whether caused by a plumbing contractor, service
company, the owner or any other person.

. Deterioration through normal wear and tear and the expense of normal maintenance.

3. Commercial application.

4. Options and accessories. American Standard’s limited warranty on these items is one year for parts only
and excludes labor. This one year limited warranty covers accessories manufactured by American
Standard (e.g. aprons, drains, grab bars, heaters, trim kits) against defects of material or workmanship.
Warranty coverage begins on the date the accessory was originally purchased by the owner.

5. Postage or shipping costs for returning products for repairs or replacement under this limited warranty and
labor or other costs incurred in connection with product removal or installation under this limited warranty.

6. ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, ALL OF WHICH ARE HEREBY
EXPRESSLY DISCLAIMED, OR THE EXTENSION BEYOND THE DURATION OF THIS LIMITED
WARRANTY OF ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR
FITNESS FOR AN INTENDED PURPOSE. (Some jurisdictions do not allow limitations on how long an
implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so these
limitations and exclusions may not apply to you.)

7. Responsibility for compliance with local code requirements. (Since local code requirements vary greatly
distributors, retailers, dealers, installation contractors and users of plumbing products should determine
whether there are any code restrictions on the installation or use of a specific product.)

This warranty gives you specific legal rights. You may have other legal rights that vary from state to state.
For service under this warranty, you should contact the following:

By Telephone:

1-800-442-1902

754063-100 Rev. B

16