American Standard 3475.5 User Manual

Installation

Instructions

COLONY/COLONY SOFT

Bidet Faucet and Transfer Valve

with Speed Connect™ Drain

Congratulations on purchasing your American Standard faucet with the Speed Connect drain, a feature found only on American Standard faucets.

Speed Connect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the ﬁrst time, every time.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

3475.500

Certiﬁed to comply with ANSI A112.18.1

M968677 Rev. 1.1

Roughing-in Dimensions

BIDET OUTLINE IS SYMBOLIC

DOUCHE SPRAY

3-7/8

BIDET FAUCET INSTALLATION

TRANSFER VALVE

(FOR FLUSHING RIM OR SPRAY)

7/8 DIA.

ADJ. 1-1/4

TO 2-1/4

1-3/8

DIA.

5-1/2

FINISHED WAL L

2-1/8

DIA.

1-1/4 O.D. TAILPIECE

1-3/16

DIA.

1-1/4

MAX.

FINISHED FLOOR

CAUTION

8 TO 12

(C)

Turn off hot and cold water supplies before beginning.

(H)

2-1/4

DIA.

4-1/4

FOR GROUND JOINT CONNECTION OR 1/2 " O.D. SLIP (INLETS)

REAR VIEW WITH

WALL REMOVED

Place RUBBER RING (10) into ESCUTCHEON (4).

Install LOCKNUT (1) and RUBBER WASHER (2) onto VALVE BODIES (3, 3a). From under side of mounting surface, install VALVE BODY (3, 3a) through valve mounting holes. Threads of VALVE BODY (3, 3a) should extent at least 5/16 of a inch above mounting surface top. Fig. A. Thread ESCUTCHEON (4) onto VALVE BODIES (3, 3a) until snug against internal stop. If necessary, adjust LOCKNUT (1).

Tighten LOCKNUTS (1) with WRENCH (5) (supplied) to secure VALVE BODIES (3, 3a).

Remove ESCUTCHEON (6), WASHER (7) and UPPER GASKET (8) from TRANSFER VALVE (9). Insert TRANSFER VALVE (9) into the center forward

Fig. A.

5/16'' MIN.

hole of BIDET.

Replace UPPER GASKET (8) and WASHER (7) and ESCUTCHEON (6) until it locks against internal stop. Position the side threaded outlet rearward and secure MOUNTING NUT (11).

3, 3a

MOUNTING SURFACE

2 1

Required tools

Screwdriver

Phillips Screwdriver

Adjustable Wrench

HOT

Plumbers' Putty or Caulking

Channel Locks

Tubing Cutter

COLD

BIDET

LEDGE

SPRAY INSTALLATION

Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside of SPRAY BODY FLANGE (2) and secure with NUT (3).

Thread SPRAY HOSE (4) with SEAL WASHER (5) to SPRAY BODY (1). Connect other end of HOSE (4) with SEAL WASHER (6) to side outlet NIPPLE (7) of the TRANSFER VALVE (8).

Thread SPRAY CAP (9) onto SPRAY BODY (1).

PUTTY

POP-UP DRAIN

Remove CLEAR PLASTIC COVER (1).

Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3).

Fig. A. Fig. B.

DRAIN BODY

Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY.

REMOVE FLANGE

Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body.

Fig. A.

Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3).

Fig. B.

Fig. A. Fig. B.

INSTALL DRAIN FROM

BELOW FIXTURE

From under side of BIDET install DRAIN BODY (1) up through drain outlet.

Note: No plumber’s putty or caulk is required. The CABLE ATTACHMENT POINT (2) must face towards the rear of the BIDET.

Install FOAM GASKET (3) and FLANGE (4) onto drain body from above BIDET and tighten FLANGE (4) ﬁrmly.

FLANGE GASKET

Check DRAIN FLANGE in BIDET to ensure that WHITE FOAM GASKET (1) is fully compressed and not visible. Fig. A.

POP-UP ROD ASSEMBLY

Insert LIFT ROD GUIDE (1) and CABLE CONNECTOR (2) through rear hole, making sure SEAL WASHER (3) is

properly seated. Fig. B.

From below slip slot in MOUNTING NUT (4) over CABLE (5). Thread NUT (4) onto lift rod guide shank to secure ROD GUIDE (1) to bidet. Hand tighten only. Fig. B.

DRAIN OUTLET

Fig. A.

FLANGE

DRAIN

TIGHTEN LOCKNUT

Tighten LOCKNUT (1) ﬁrmly with Adjustable Wrench or Channel Locks.

Fig. B.

WHITE FOAM

GASKET NOT VISIBLE

ILLUSTRATION SHOWN LESS VALVES

M968677 Rev. 1.1

SLOTTED MOUNTING NUT

ATTACH CABLE

CONNECTOR

Fig. A.

Fig. B.

Fig. C.

POP-UP KNOB (1) must be fully down. Fig. A.

Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. B.

Your new POP-UP DRAIN installation is now complete.

Fig. C.

Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. C.

CHECK OPERATION OF POP-UP

Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.

Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.

INSTALL DIVERTER KNOB

Push DIVERTER KNOB (1) onto HANDLE ADAPTER (2).

DOWN

1-1/4” O.D.

5 4

Push on RING (3) and tighten with SCREW (4).

Press on KNOB CAP (5). Note: Screwdriver gap is for disassembling and should point downwards.

Insert SEAL (1) into ADAPTER (2) and tighten ADAPTER (2) to side of TRANSFER VALVE (3).

Install SEAL (4) into coupling nut of TEE (5) and tighten connection to ADAPTER (2).

Connect HOSE COUPLING NUTS (6) to Hot and Cold valve bodies and securely tighten.

WATER SUPPLY CONNECTION

NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY.

Connect water supply to VALVE BODIES (7,7a) with 1/2" IPS FLEXIBLE SUPPLIES (8) or 3/8" O.D. BULL-NOSE RISERS (9). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length.

Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS.

Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet.

TEE AND HOSE CONNECTION

OUTLINE OF BIDET

1/2" PIPE

THREAD

FLEXIBLE

SUPPLIES

HOT

3/8 COMPRESSION CONNECTION

Front

COLD

CONNECT TO WASTE OUTLET

COUPLING NUT

3/8 O.D.

BULL-NOSE

RISERS

COMPRESSION NUT

FERRULE

M968677 Rev. 1.1

INSTALL HANDLES

LEVER HANDLE

Turn HANDLE STEM (1) to "OFF" position.

Place the HANDLE ADAPTER (2) on the HANDLE STEM (1). Install the ADAPTER SCREW (3) and tighten securely.

Position LEVER HANDLE (4) and place on ADAPTER (2). Install the HANDLE SCREW (5) and tighten securely.

TEST INSTALLED FITTING

With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks.

Operate both HANDLES (1) to ﬂush water lines thoroughly.

Rotate TRANSFER VALVE (5) from rim wash to spray several times to check operation.

CHECK DRAIN CONNECTIONS

Pull up POP-UP KNOB (3) and ﬁll Sink with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Bidet. If STOPPER (4) does not seal properly, please refer to “Troubleshooting Guide” in these instructions.

Push POP-UP KNOB (3) down and check all drain connections and "P" trap for leaks. Tighten if necessary.

OUTLINE OF BIDET

SPRAY

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.

CARE INSTRUCTIONS:

SERVICE

To change direction of handle rotation, proceed as follows:

Turn VALVE to OFF position. Loosen HANDLE SCREW (1) . Pull HANDLE (2) off ADAPTER (4). Loosen ADAPTER

SCREW (3) and pull off ADAPTER (4). Remove SPRING CLIP (7). Lift STOP WASHER (5), turn 90° and replace. Replace SPRING CLIP (7). Reinstall ADAPTER SCREW (4) and LEVER HANDLE (2).

Tighten HANDLE SCREW (1). If spout drips, operate handles several

times from OFF to ON position. Do not force - handles turn only 90˚.

90˚

M968677 Rev. 1.1

+ 8 hidden pages