American Standard 3461, 3462, 3463, 3464, 3465 Checked
...
INSTALLATION
INSTRUCTIONS
MADERA 16-1/2" HEIGHT FLUSH VALVE
FLOOR MOUNTED TOILETS
Model 3461, 3462, 3463, 3464, 3465, 3466
Meets the American Disabilities Act Guidelines and ANSI A117.1
Requirements for the Physically Challenged
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations may
require professional help.) Also be sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FOR
!
HANDLING TO AVOID BREAKAGE AND POSSIBLE INJURY!
NOTE: For proper operation product requires a minimum of 30 psi working line pressure
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Sealant
1
Pictures may not exactly define contour of china
Regular Screwdriver
Adjustable Wrench
Tape Measure
Carpenters Level
Flush Valve
2
1" N.P.T. OR 1" C.W.T. SUPPLY
419mm
(16-1/2)
FINISHED
FLOOR
TO FLUSH VALVE
121mm
(4-3/4)
356mm
(14)
238mm
(9-3/8)
1 - 1/2
SPUD
730mm
(28-3/4)
FINISHED WALL
Model 3461, 3462, 3465, 3466 Model 3463, 3464
718mm
(28-1/4)
13mm
(1/2)
254mm
(10)
102mm
(4)
25mm
(1)
150mm
(5-7/8)
C/L OF OUTLET
470mm
(18-1/2)
C/L OF SEAT POST HOLES
140mm (5-1/2) CENTERS
338mm
(13-5/16)
FINISHED WALL
76mm
(3)
13mm
(1/2)
254mm
(10)
718mm
(28-1/4)
C/L OF SEAT POST HOLES
140mm (5-1/2) CENTERS
338mm
(13-5/16)
150mm
(5-7/8)
C/L OF OUTLET
470mm
(18-1/2)
3
CLOSET FLANGE
10"
254mm
SEALANT
438mm
(17-1/4)
419mm
(16-1/2)
FINISHED
FLOOR
356mm
(14)
238mm
(9-3/8)
WAX RING
SAVE FOR FUTURE USE
CLOSET BOLTS
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90°, and slide
into place 6" (152 mm) apart and parallel to wall.
Product names listed herein are trademarks of AS Americas Inc.
© AS Americas Inc. 2008
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet. Apply a thin bead of
sealant around toilet base.
7301166-100 Rev. A
4
5
BOLT CAP
CLOSET
BOLT
NUT
TAPERED
WASHER
WASHER
CLOSET FLANGE
CLOSET BOLT
NUT
FLANGE
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking
motion, press bowl down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly seated on
floor.
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange
so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers
marked "THIS SIDE UP" must face up!
b. Install caps on washers. (If necessary, cut bolt height to
size before installing caps.)
!
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
c. Smooth off the bead of sealant around base. Remove
excess sealant.
AMERICAN-STANDARD ONE-YEAR LIMITED WARRANTY
If inspection of this American-Standard plumbing product, within one year after its initial installation, confirms that it is defective
in materials or workmanship, American-Standard will repair or, at its option, exchange the product for a similar model.
This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of
this product should check with a local building or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty
maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with American-Standard's
instructions; or if it has been modified in a manner inconsistent with the product as shipped by American-Standard.
American-Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of
removal or installation, nor shall American-Standard be responsible for any other incidental or consequential damages
attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded
from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may
not apply to you.)
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province
to province, in which case this warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the
product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the
following address:
In the United States:
American Standard Inc.
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States,
warranty information may also be
obtained by calling the following
toll free number: (800) 442-1902
www.americanstandard-us.com
7301166-100 Rev. A
In Canada:
American-Standard
2480 Stanfield Road
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: (800) 387-0369
www.americanstandard.ca
- 2 -
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
www.americanstandard.com.mx
Loading...