American Standard 2806.028WC, 2806.018WC User Manual

HERITAGE 6'™ WHIRLPOOL

❏ 2806.018WC Whirlpool Featuring System I:

• Acrylic with  berglass reinforcement

• EverClean™ whirlpool system featuring Antimicrobial AlphaSan

• Pre-leveled tub bottom

• Dual, molded-in arm rests

• Integral faucet deck area

• 2.0 HP, two speed, self-draining pump/motor

• Factory installed power cord and plug

• Eight multi-directional and  ow-adjustable jets including:

- Two Ideal- ow jets

- Four body massage jets

- Two recessed back-rest jets

• Deck-mounted air switch On/Off

• Two silent air volume controls

• Quick Connect Safe-T-Heater connection system

• Factory installed and tested whirlpool system

HERITAGE 6'™

WHIRLPOOL

HIGH GLOSS

❏ 2806.028WC Whirlpool Massage Featuring

System II

Same as 2806.018WC except:

• 2.0 HP, two speed self-draining pump/motor with dry run seal and Pulse feature

• Deck-mounted electronic On/Off with 20 minute built-in timed safety shut off and chrome bezel

Nominal Dimensions: 1829 x 908 x 546mm (72" x 35-3/4" x 21-1/2")

Compliance Certi cations -

Meets or Exceeds the Following Speci cations:

• Underwriters Laboratories - Hydromassage Bathtubs UL 1795

• ASME A112.19.7M for Whirlpool Appliances

• ANSI Z124.1 for Plastic Bathtubs

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

SEE REVERSE FOR ROUGHING-IN DIMENSIONS AND PRODUCT SPECIFICATIONS

To B e S p e ci  ed - Required:

❏ Color: ❏ Bath Filler: (specify  nish) ❏ Bath Drain: 1583.470 (specify  nish)

To Be Speci ed - Optional:

❏ Safe-T-Heater*: 9075.120 ❏ Grab Bar Kit: 9822-200-two per kit (specify color) ❏ System II Control Bezel: 9861.100 (specify  nish

For color/ nish availability and other faucet choices, please see the Product Selector and Pricing Guide.

* NOTE: the Safe-T-Heater is designed to maintain water temperature during operation. It will not heat cold water to desired bathing temperature.

H35

Revised 6/07

279mm

(11)

1829mm

(72)

HERITAGE 6'™

WHIRLPOOL

HIGH GLOSS

908mm

(35-3/4)

FITTING DECK

OVERFLOW

INTEGRAL

SUPPORT

457mm

(18)

INTEGRAL

140mm

(5-1/2)

C/L OF

FEET

108mm (4-1/4)

51mm

(2)

ROUGH

FLOOR

1-1/2 N.P.T.M. THREADS

1-1/2 O.D.TAILPIECE

INSTALLED SIZE WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW WHIRLPOOL MIN. OPERATING VOL. BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS.

CUBE (FT3)

SYSTEM I PUMP SYSTEM II PUMP

GENERAL SPECIFICATIONS FOR 2806 WHIRLPOOL

229 x 330mm (9 X 13) FLOOR CUTOUT

ON/OFF

SWITCH

C/L OF DRAIN OVERFLOW

WHIRLPOOL ELECTRICAL SPECIFICATIONS

OUTLINE OF

CUTOUT

LEVELING STRINGER (NOT FOR SUPPORT)

72 x 35-3/4 x 21-1/2 In. (1829 x 908 x 546mm)

TO PUMP FOR SERVICE ON ALL INSTALLATIONS

51mm

(2)

744 Lbs. (338 Kg.)

45 x 24 In. (1143 x 610mm)

60 x 30 In. (1524 x 762 mm)

41 Lbs./Sq.Ft. (198 Kgs./Sq.m)

2.1 HP, 14.4 AMPS ,120V.

2.1 HP, 15.6 AMPS ,120V.

PROVIDE ACCESS

546mm

(21-1/2)

495mm

(19-1/2)

108mm (4-1/4)

135 Lbs. (61 Kg.)

73 Gal. (276 L) 44 Gal. (167 L)

15 In. (381mm)

25.6

49.4

PUMP

SAFE-T-HEATER REMOVABLE BLANK

NOTES:

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.

■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.

▲ CUTOUT TEMPLATE PROVIDED IN SHIPPING BOX. MAY BE REQUESTED SEPARATELY. OPTIONAL GRAB BAR KIT AVAILABLE

AND MUST BE ORDERED SEPARATELY.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

● IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING

SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.

SUPPLY PIPING NOT INCLUDED.

IMPORTANT: Dimensions of  xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

H36

Revised 6/07