American Standard 2794, 2795 Installation Manual
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Studio® Dual Flush Concealed Trapway
Right Height®, Elongated Model 2794
Right Height
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations
may require professional help.) Also be sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure
Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level
1 REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
2
ROUGHING-IN
DIMENSIONS:
NOTE: Distance from wall to
closet flange centerline must
be as listed below:
IMPORTANT: Water supply
on the wall is required at
2-1/4" or 8" from centerline
of the toilet (see rough-in).
First suggested position is
hidden behind the toilet. The
geometry of the toilet gives
space for this installation.
The second suggested
position is next to the toilet.
Between these two
positions, the space for the
supply between wall and
toilet is limited to 4-1/2". In
this case, check your supply
and hose dimensions.
®
, Round Front Model 2795
RIGHT HEIGHT ELONGATED 2-PIECE TOILET
FINISHED
WALL
8-3/4"
(221mm)
1-1/8"
(29mm)
2-5/8"
(67mm)
3-1/8"
(81mm)
4-1/2"
(114mm)
RIGHT HEIGHT ROUND FRONT 2-PIECE TOILET
1-1/8"
(29mm)
2-5/8"
(67mm)
3-1/8"
(81mm)
7-1/2"
(191mm)
12"
(305mm)
IMPORTANT: Water supply on the wall is required at 2-1/4" or 8" from centerline of the toilet (see rough-in).
First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.
The second suggested position is next to the toilet. Between these two positions, the space for the supply
FINISHED
between wall and toilet is limited to 4-1/2". In this case, check your supply and hose dimensions.
WALL
8-3/4"
(221mm)
C/L OF SEAT POST
HOLES 5-1/2"
(140mm) CENTERS
30-1/4"
(768mm)
C/L OF SEAT POST
HOLES 5-1/2"
(140mm) CENTERS
18-1/2"
(470mm)
13-11/16"
(347mm)
28-1/4"
(717mm)
16-1/2"
(419mm)
16-1/2"
(419mm)
16-1/2"
(419mm)
FINISHED
FLOOR
SUPPLY
REQUIRED
(position 1
position 2)
SUPPLY
AS
REQUIRED
(position 1 or
position 2)
5-1/2"
(140mm)
AS
or
5-1/2"
(140mm)
8"
(204mm)
8"
(204mm)
15-3/4"
(399mm)
(356mm)
12-3/16"
(309mm)
15-3/4"
(399mm)
(356mm)
14"
2-1/4"
(57mm)
14"
2-1/4"
(57mm)
6"
(152mm)
30-7/8"
(784mm)
30-7/8"
(784mm)
Certified by
IAPMO R&T
BACK VIEW
(for reference)
SAVE FOR FUTURE USE
4-1/2"
(114mm)
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2012
IMPORTANT: Water supply on the wall is required at 2-1/4" or 8" from centerline of the toilet (see rough-in).
First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.
The second suggested position is next to the toilet. Between these two positions, the space for the supply
between wall and toilet is limited to 4-1/2". In this case, check your supply and hose dimensions.
(191mm)
12"
(305mm)
7-1/2"
12-7/8"
(328mm)
FINISHED
FLOOR
12-3/16"
(309mm)
6"
(152mm)
BACK VIEW
(for reference)
7301692-100 Rev. C
3 4 5
Press firmly.
6 7 8
TIP: Place 2 pieces of masking
tape on floor (as shown) to help
with alignment in step 6.
Apply weight evenly. Do not move after
placement. Water tight seal may break.
9 10
Thread, then
hand tighten
water supply.
Hand Tighten Only.
!
Do Not Overtighten.
Tighten handles alternately
until tank contacts bowl.
HAND TIGHTEN ONLY!
For seat installation,
*
see instructions
included with seat.
!
WARNING:
Overtightening of water supply
line nuts could result in breakage
and potential flooding. If the
connection leaks after hand
tightening, replace the supply line.
Do not use any type of sealant on
the water supply connection.
Use of plumber’s putty,
!
pipe dope, or any other
type of sealant will void
the warranty.
- 2 -
7301692-100 Rev. C
Loading...