American Standard 2586, 2018, 2793, 3186, 2414 User Manual

...

INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE

Champion®4 2-piece Toilets

Models - 2002, 2018, 2023, 2414, 2585, 2792, 2586, 2793, 3186, 3404

Doral Classic™ Champion®4 2-piece Toilets Models - 2058, 2074, 2076, 2473

Doral™ Champion®4 2-piece Toilets Models - 2367, 2368, 2369, 2443

Oakmont™ Champion®4 2-piece Toilets Models - 2625, 2627, 2738

Townsend™ Champion®4 2-piece Toilets Models - 2733, 2735

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE: Pictures may not exactly define contour of china and components.

NOTE: BACK-TO-BACK INSTALLATION

Depending upon your plumbing and venting conditions, the flow

from the Champion in a back-to-back installation may create a vacuum on the system and draw water from the opposing bowl. The National Standards Plumbing Code prohibits the use of a cross fitting for drainage as throw over is possible. The code does approve a directional "Y" style fitting with proper venting to direct the water downward and away from the other toilet.

Recommended fitting type for back-to-back installations.

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant Hacksaw Wax Ring/Gasket Flexible Supply Tube 1/2" Deep Well Nut Driver or Closet Bolts Tape Measure Carpenters Level Deep Well Socket Wrench

REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl. b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply! c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases. d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed!

SAVE FOR FUTURE USE

Product names listed herein are trademarks of AS America, Inc. © AS America, Inc. 2010

730529-100 Rev. T

NOTE: DRAWINGS ARE FOR DIMENSIONAL PURPOSES ONLY. THEY ARE NOT EXACT REPRESENTATIONS.

ROUGHING-IN DIMENSIONS: Right Height™ Elongated Two Piece Toilet

FINISHED WALL

Right Height

19mm ± 6mm

(1 ± 1/4

772mm

(30-3/8

721mm

(28-3/8

470mm

(18-1/2

419mm

(16-1/2

™

Round Front Two Piece Toilet

356mm

(14

ROUGHING-IN DIMENSIONS: Normal Height Elongated Two Piece Toilet

FINISHED WALL

Normal Height Round Front Two Piece Toilet

19mm ± 6mm (1 ± 1/4

721mm

(28-3/8

772mm

(30-3/8

470mm

(18-1/2

419mm

(16-1/2

356mm

(14

ROUND FRONT

MODELS

83mm

(3-1/4

305mm

(12

SUPPLY

419mm

(16-1/2

16mm

(5/8

FINISHED FLOOR

REQ'D

254mm

(10

152mm

83mm

(3-1/4

16mm

(5/8

305mm

(12

387mm

(15-1/4

FINISHED FLOOR

SUPPLY

REQ'D

254mm

(10

152mm

DIMENSIONS

MODEL

2002, 2414, 2586, 235mm (9-1/4) 264mm (10-3/8) 362mm (14-1/4) 464mm (18-1/4) 825mm (32-1/2) 254mm (10)

2793, 3186, 3404 2018, 2023, 2585, 2792 235mm (9-1/4) 264mm (10-3/8) 362mm (14-1/4) 464mm (18-1/4) 797mm (31-3/8) 254mm (10)

2058 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 479mm (18-7/8) 873mm (34-3/8) 254mm (10) 2074, 2076 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 479mm (18-7/8) 851mm (33-1/2) 254mm (10) 2367 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 492mm (19-3/8) 872mm (34-5/16) 254mm (10) 2368, 2369 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 492mm (19-3/8) 844mm (33-1/4) 254mm (10) 2625, 2627 216mm (8-1/2) 273mm (10-3/4) 381mm (15) 492mm (19-3/8) 844mm (33-1/4) 286mm (11-1/4) 2738 216mm (8-1/2) 275mm (10-13/16) 384mm (15-1/8) 492mm (19-3/8) 872mm (34-5/16) 295mm (11-5/8) 2733, 2735 216mm (8-1/2) 267mm (10-1/2) 379mm (14-7/8) 479mm (18-7/8) 873mm (34-3/8) 284mm (11-3/16)

ABCDE F

CLOSET FLANGE

CLOSET BOLTS

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn 90°, and slide into place 6" (152 mm) apart and parallel to wall.

MANIFOLD INSIDE WATERWAY – DO NOT REMOVE

FLANGE

CLOSET

BOLT

NUT

TAPERED WASHER

SEALANT

WAX RING

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange, with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base.

POSITION TOILET ON FLANGE

a. Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes. b. Loosely install retainer washers and nuts. Side of washers marked "THIS SIDE UP" must face up!

- 2 -

730529-100 Rev. T

+ 3 hidden pages