American Standard 2476.216, 2476.516, 2480.516, 2480.216, 2484.516 User Manual
...
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
FloWise™ DUAL FLUSH 2-PIECE TOILET
Model 2479.216 / 2479.516 / 2476.216 / 2476.516 / 2779.516
Model 2480.216 / 2480.516 / 2484.216 / 2484.516 / 2778.516 /
2566.216 Right Height™
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be
sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure
Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level
REMOVE OLD TOILET
1
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line.
NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
ROUGHING-IN DIMENSIONS:
2
111mm
(4-3/8)
FINISHED WALL
41mm ± 6mm
(1-5/8±1/4)
197mm
(7-3/4)
121mm
(4-3/4)
305mm
(12)
CLOSET
FLANGE
C/L OF OUTLET
Models: 2479.216 / 2479.516 /
2476.216 / 2476.516 / 2779.516
794mm
(31-1/4)
470mm
(18-1/2)
C/L OF SEAT POST HOLES
140mm (5-1/2 CENTRES)
397mm
(15-5/8)
A
CLOSET
BOLTS
375mm
(14-3/4)
FINISHED
FLOOR
SUPPLY
AS
REQ'D
203mm
114mm
43
(8)
(4-1/2)
SEALANT
432mm
(17)
C/L
371mm
(14-5/8)
251mm
(9-7/8)
PUSH
BUTTON
765mm
(30-1/8)
111mm
WAX RING
Models: 2480.216 / 2480.516 / 2484.216 / 2484.516 /
2778.516 / 2566.216 Right Height™
(4-3/8)
FINISHED WALL
41mm ± 6mm
(1-5/8±1/4)
197mm
(7-3/4)
121mm
(4-3/4)
305mm
(12)
794mm
(31-1/4)
470mm
(18-1/2)
C/L OF SEAT POST HOLES
140mm (5-1/2 CENTRES)
410mm
(16-1/8)
C/L OF OUTLET
448mm
(17-5/8)
FINISHED
FLOOR
*SUPPLY
AS
REQ'D
203mm
114mm
5
(8)
(4-1/2)
Certified by
IAPMO R&T
432mm
(17)
C/L
370mm
(14-5/8)
265mm
(10-3/8)
PUSH
BUTTON
BOLT
CAP
NUT
TAPERED
WASHER
829m
(32-5/8)
m
SAVE FOR FUTURE USE
INSTALL CLOSET BOLTS
Install closet bolts in flange channel,
turn 90°, and slide into place 6"
(152mm) apart and parallel to wall.
TEMPORARILY set toilet in place.
Place tapered washer and nuts onto
the bolts as shown in Step 5. Mark bolt
length needed for bolt cap clearance.
Remove toilet. Precut the bolts to
length by twisting the nut onto the bolt
past the cut mark, then cutting the bolt
to the desired length with a hacksaw.
Unscrew the nut to repair the threads.
INSTALL WAX SEAL
Invert toilet on floor (cushion to
prevent damage), and install wax
ring evenly around waste flange
(horn), with tapered end of ring
facing toilet. Apply a thin bead of
sealant around toilet base.
Re-install bolts in flange.
Product names listed herein are trademarks of AS America Inc.
© AS America Inc. 2008
CLOSET
BOLT
FLANGE
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange
so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers
marked "THIS SIDE UP" must face up!
7301144-100 Rev. F
6
7
Tank Installation Kit Includes:
2 bolts, 2 rubber washers, 4 metal washers, 4
metal nuts, 2 plastic nuts, 1 large rubber gasket.
RUBBER
WASHER
BOLT CAP
CLOSET FLANGE
WASHER
NUT
CLOSET BOLT
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking
motion, press bowl down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly seated on floor.
!
CAUTION:
DO NOT OVERTIGHTEN NUTS
b. Install caps on washers.
c. Smooth off the bead of sealant around base.
Remove excess sealant.
TANK MTG.
BOLTS
WASHER
NUT
WASHER
NUT
RUBBER
GASKET
INSTALL TANK
a. Discard plastic nuts.
b. Install tank mounting bolts and rubber
washers from inside tank, through
mounting holes and secure with one
metal washer and one nut per bolt.
c. Install large rubber gasket over threaded
outlet on bottom of tank and lower tank
onto bowl so that tapered end of gasket
fits evenly into bowl water inlet opening.
d. With tank parallel to wall, secure tank to
bowl using remaining two metal washers
and nuts. Alternately tighten nuts until
tank is snugged down evenly against
bowl surface.
USE NUT DRIVER OR DEEP SOCKET RACHET.
*
!
CAUTION:
DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT!
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
8
9a
Before continuing, determine the type of water supply connection you have from
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
METAL / COPPER
FLARED TUBING
CONE
WASHER
COUPLING
NUT
WATER
SHUT-OFF
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in
water leakage. Water supply
tube or pipe must extend at
least 1/2" inside threaded
shank of valve (does not
apply to flanged tubing).
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
METAL FLANGED
TUBING
EXISTING
WASHER
EXISTING
COUPLING
NUT
WATER
SHUT-OFF
Use existing
coupling nut
and washer.
METAL SPIRAL
TUBING
WATER
SHUT-OFF
Use existing spiral
cone washer.
Fluidmaster cone
washer may not
seal completely on
spiral type supply
line.
EXISTING
CONE
WASHER
COUPLING
NUT
VINYL / BRAIDED
CONNECTOR
Captive cone
washers already
included. No
additional washers
needed.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
LOCK NUTLOCK NUT LOCK NUT LOCK NUT
COUPLING
NUT
WATER
SHUT-OFF
9b
With correct washers in
place (see Step 9a),
tighten COUPLING NUT
1/4 turn beyond hand tight.
DO NOT OVERTIGHTEN.
- 2 -
7301144-100 Rev. F
Loading...