American Standard 2775.002, 2775.018WC, 2775.018W User Manual
CADET™ CORNER
WHIRLPOOL & BATHING POOL
HIGH GLOSS ACRYLIC
CADET CORNER WHIRLPOOL & BATHING POOL
❏ 2775.018W Whirlpool featuring System I
• Acrylic with fiberglass reinforcement
• Pre-leveled tub bottom
• Dual, backrest positions
• Molded-in arm rests
• 2.0 HP single speed, self-draining pump/motor
• Factory installed power cord with plug
• Eight multi-directional and flow-adjustable
jets including:
- Two Ideal-flow jets
- Two body massage jets
- Four recessed back-rest jets (two in
each backrest)
• Deck-mounted air switch On/Off
• Two silent air volume controls
• Quick Connect Safe-T-Heater connection
system
• Factory installed and tested whirlpool system
❏ 2775.018WC Stay Clean™ Whirlpool Massage
Featuring System I:
• Same as 2775.018W except with the
StayClean™ whirlpool system featuring
Antimicrobial AlphaSan®
❏ 2775.002 Bathing Pool only
Nominal Dimensions: 2159 x 1524 x 502mm
(85” x 60” x 19-3/4")
© 2003 American Standard Inc.
BV-21
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
Rev. 3/03
Compliance Certifications Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
To Be Specified - Required:
❏ Color:
❏ Bath Filler: (specify finish)
❏ Bath Drain: 1583.470 (specify finish)
To Be Specified - Optional:
❏ Safe-T-Heater*: 9075.120
❏ Jet Trim Ring Kit: 9860.200-two per kit
(Specify finish)
❏ Universal Tile Bead Kit: 751755-100
❏ Grab Bar Kit: 9822.200-two per kit (specify finish)
For color/finish availability and other faucet choices,
please see the Product Selector and Pricing Guide.
* NOTE: the Safe-T-Heater is designed to maintain water
temperature during operation. It will not heat cold water to
desired bathing temperature.
CADET™ CORNER
WHIRLPOOL & BATHING POOL
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA
TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT
REQUIRED. ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL
INFORMATION.
OPTIONAL 2 WALL TILING BEAD KIT AVAILABLE AND MUST BE ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI
Standard Z124.1/A112.19.7M.
These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided leaflet.
■
RECOMMENDED
FITTING LOCATION
64 X 330mm (2-1/2 X 13)
38 mm REF.
(1-1/2)
ROUGH
FLOOR
INTEGRAL
SUPPORT
FEET
1524mm
(60)
OUTLINE OF
CUTOUT
1080 mm
(42-1/2)
C/L OF
OVERFLOW
1-1/2 N.P.T.M.
THREADS
1-1/2 O.D. TAILPIECE
165mm
(6-1/2)
2159mm
(85)
76mm
(3)
1080mm
(42-1/2)
70mm REF.
(2-3/4)
C/L
279mm
(11)
C/L OF
DRAIN OUTLET
LEVELING STRINGER
NOT FOR SUPPORT
70mm
(2-3/4)
229 X 305mm
(9 X 12)
CUTOUT IN
FLOOR FOR
DRAIN
SAFE-THEATER
REMOVABLE
BLANK
ON/OFF
SWITCH
PUMP
117mm
(4-5/8)
1076mm
(42-3/8)
1524mm
(60)
PROVIDE ACCESS
TO PUMP FOR
SERVICING ON ALL
INSTALLATIONS
502mm
(19-3/4)
464mm
(18-1/4)
RECOMMENDED
FITTING LOCATION
64 X 330mm (2-1/2 X 13)
38 mm REF.
(1-1/2)
ROUGH
FLOOR
INTEGRAL
FEET
1524mm
(60)
OUTLINE OF
CUTOUT
1080 mm
(42-1/2)
C/L OF
OVERFLOW
1-1/2 N.P.T.M.
THREADS
1-1/2 O.D. TAILPIECE
165mm
(6-1/2)
2159mm
(85)
76mm
(3)
229 X 305mm
(9 X 12)
1076mm
CUTOUT IN
(42-3/8)
FLOOR
FOR
DRAIN
70mm REF.
(2-3/4)
C/L
279mm
(11)
C/L OF
DRAIN OUTLET
LEVELING STRINGER
NOT FOR SUPPORT
70mm
(2-3/4)
117mm
(4-5/8)
464mm
(18-1/4)
1524mm
(60)
502mm
(19-3/4)
GENERAL SPECIFICATIONS FOR 2775 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
85 X 60 X 19-3/4In.(2159 X 1524 X 502mm)
130 Lbs. (59 Kg.)
756 Lbs. (343 Kg.)
75 Gal. (284 L.)
60 Gal. (227 L.)
32 X 32 In. (813 mm X 813 mm)
46 X 46 In. (1168 X 1168mm)
14 In. (356 mm)
34 Lbs./Sq. Ft. (115 Kgs/Sq. m.)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
2.1 HP, 14.4 AMPS, 120V.SYSTEM I PUMP
41.7
70.4
GENERAL SPECIFICATIONS FOR 2775 BATHING POOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
(2159mm X 1524 mm X 502mm)
32 X 32 In. (813 mm X 813 mm)
33 Lbs./Sq. Ft. (111 Kgs/Sq. m.)
85 X 60 X 19-3/4In.
105 Lbs. (48 Kg.)
730 Lbs. (328 Kg.)
75 Gal. (284 L.)
46 X 46 In. (1168 X 1168mm)
14 In. (356 mm)
41.7
70.4
Loading...