American Standard 2773.018WC, 2773.018W, 2773.002 User Manual
CADET™ 6’ X 36”
WHIRLPOOL & BATHING POOL
HIGH GLOSS ACRYLIC
CADET™ 6’ X 36” WHIRLPOOL & BATHING POOL
❏ 2773.018W Whirlpool featuring System I
• Acrylic with fiberglass reinforcement
• Pre-leveled tub bottom
• Form-fitted backrest position
• Dual, molded in arm rests
• 2.0 HP single speed, self-draining pump/motor
• Factory installed power cord with plug
• Eight multi-directional and flow-adjustable
jets including:
- Two Ideal-flow jets
- Four body massage jets
- Two recessed back-rest jets
• Deck-mounted air switch On/Off
• Two silent air volume controls
• Quick Connect Safe-T-Heater connection
system
• Factory installed and tested whirlpool system
❏ 2773.018WC Stay Clean™ Whirlpool Massage
Featuring System I:
• Same as 2773.018W except with the
StayClean™ whirlpool system featuring
Antimicrobial AlphaSan®
❏ 2773.002 Bathing Pool only
Nominal Dimensions: 1829 x 908 x 502mm
(72” x 35-3/4” x 19-3/4")
© 2003 American Standard Inc.
BV-23
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
Rev. 3/03
Compliance Certifications Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
To Be Specified - Required:
❏ Color:
❏ Bath Filler: (specify finish)
❏ Bath Drain: 1583.470 (specify finish)
To Be Specified - Optional:
❏ Safe-T-Heater*: 9075.120
❏ 6 Foot Acrylic Apron: 9372.018 (specify color)
❏ 6 Foot Apron: 9272.018 (specify color)
❏ Jet Trim Ring Kit: 9860.200-two per kit
(Specify finish)
❏ Universal Tile Bead Kit: 751755-100
❏ Grab Bar Kit: 9822.200-two per kit (specify finish)
For color/finish availability and other faucet choices,
please see the Product Selector and Pricing Guide.
* NOTE: the Safe-T-Heater is designed to maintain water
temperature during operation. It will not heat cold water to
desired bathing temperature.
CADET™ 6’ X 36”
WHIRLPOOL & BATHING POOL
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA
TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT
REQUIRED. ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL
INFORMATION.
OPTIONAL 3 WALL TILING BEAD. KIT AND APRON No. 9272.018 or 9372.018 AVAILABLE AND MUST BE
ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI
Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided leaflet.
■
229mm
SEE FITTING
SPECS FOR
DIMENSIONS
908 mm
(35-3/4)
SUPPLIES
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
1651 & 1981mm
(9)
FINISHED
WALL
454 mm
(17-7/8)
C/L OF
(65 & 78)
19 mm
(3/4)
305 mm
(12)
57mm
(2-1/4)
C/L OF DRAIN
C/L OF
OVERFLOW
70mm
(2-3/4)
ROUGH
FLOOR
INTEGRAL
SUPPORT
229 mm
CUTOUT IN FLOOR
FOR DRAIN
38 mm
(1-1/2)
502 mm
(19-3/4)
FEET
PROVIDE ACCESS TO PUMP FOR
SERVICING ON ALL INSTALLATIONS
1829 mm
(72)
RECOMMENDED FITTING LOCATION
64 X 330mm (2-1/2 x 13")
FOR PIER OR ISLAND
INSTALLATIONS ONLY
(9)
102 mm
(2) AIR VALVES
ALT. FITTING
LOCATION #1
(4)
(8) JETS
305mm
(12)
1-1/2 N.P.T.M.
THREADS
1-1/2 O.D.TAILPIECE
PUMP
C/L OF
SHOWER ARM
C/L OF
VALVES
C/L OF
SPOUT
70 mm
(2-3/4)
117 mm
(4-5/8)
ON/OFF
SWITCH
OUTLINE OF CUTOUT
1791 mm x 870 mm
(70-1/2 X 34-1/4)
SAFE-T-HEATER
REMOVABLE
BLANK
■ LEVELING STRINGER
NOT FOR SUPPORT
464 mm
(18-1/4)
229mm
SEE FITTING
SPECS FOR
DIMENSIONS
908 mm
(35-3/4)
454 mm
(17-7/8)
C/L OF
SUPPLIES
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
1651 & 1981mm
(65 & 78)
(9)
19 mm
FINISHED
WALL
(3/4)
305 mm
(12)
57mm
(2-1/4)
C/L OF DRAIN
C/L OF
OVERFLOW
70 mm
(2-3/4)
502 mm
(19-3/4)
ROUGH
FLOOR
INTEGRAL
SUPPORT
FEET
1829 mm
RECOMMENDED FITTING LOCATION
229 mm
(9)
CUTOUT IN FLOOR
FOR DRAIN
38 mm
(1-1/2)
1-1/2 N.P.T.M.
1-1/2 O.D.TAILPIECE
(72)
64 X 330mm (2-1/2 x 13")
FOR PIER OR ISLAND
INSTALLATIONS ONLY
ALT. FITTING
LOCATION
305 mm
(12)
102 mm
(4)
THREADS
OUTLINE OF CUTO
1791 mm x 870 mm
C/L OF
VALVES
70 mm
(2-3/4)
C/L OF
SPOUT
117 mm
(4-5/8)
(70-1/2 X 34-1/4)
464 mm
(18-1/4)
C/L OF
SHOWER ARM
■ LEVELING STRINGER
NOT FOR SUPPORT
GENERAL SPECIFICATIONS FOR 2773 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
72 x 35-3/4 x 19-3/4 In.(1829 x 908 x 502mm)
101 Lbs. (45 Kg.)
751 Lbs. (341 Kg)
78 Gal. (296 L.)
64 Gal. (243 L.)
23 x 49 In. (584 mm x 1245 mm)
65 x 29 In. (1651 x 737 mm)
13-1/2 In. (343 mm)
40 Lbs./Sq. Ft. (190 Kgs/Sq. m.)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
2.1 HP, 14.4 AMPS, 120V.SYSTEM I PUMP
23.8
48.3
GENERAL SPECIFICATIONS FOR 2773 BATHING POOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
72 x 35-3/4 x 19-3/4 In.
(1829mm x 908 mm x 502mm)
76 Lbs. (34 Kg.)
725 Lbs. (326 Kg.)
78 Gal. (296 L.)
23 x 49 In. (584 mm x 1245 mm)
65 x 29 In. (1651 x 737 mm)
13-1/2 In. (343 mm)
38 Lbs./Sq. Ft. (183 Kgs/Sq. m.)
23.8
48.3
Loading...